hi - congratulations on getting this out - looks like a great system! curious about the network protocol, are you using CAN? also, what's the ETA on the SDK? ...
Hello Jeff, Thanks! We have been getting many positive reactions to our system, so we think we're on to something. The network protocol is our own proprietary...
Hi everyone, We've just put up our first release of Teleo Max for Mac OS X. The main difference between the last beta release and this current release is that...
Hi, I've been asked if Teleo would have any trouble with overdrive enabled. I've done some experiments and looked over our critical code and I see no reason...
hi I do have absolutely no chance in getting teleo working config : Mac Sys 9.2, Max/MSP 4.1 (powerbook and Quicksilver G4 tested) system extensions reduced to...
btw : i did the Z-term routine as described on the list earlier. It seems to do what it is supposed to. looks fine. but it crashes max as soon as i call...
hi list since some of you might have experience: I am trying servo motors and a few questions arise using teleo with carson 13374 "standard" servos a) my...
Hello Wolf, (a,b) Just within the last 30 minutes we found and fixed a bug in the servo module firmware which caused this problem. In order to get the new ...
I have been trying to drive stepper motors with Teleo's digital out module but I have not been successful. Once in a while a pulse gets lost (about one pulse...
... I guess the system overall datarate is just too slow for actually driving hundreds of pulses a second. But this brings me to the following idea : Why not...
Hello Jean, We have been able to duplicate this problem in our lab and will work to find a solution. The rates you report are about what we observe. Meanwhile,...
Wolf Thanks for your suggestion. Yes, I think one could easily convert MSP audio into pulses. But this would not work for me since I need to drive several ...
Hello Michael, Thank you for your prompt answer. You guys are very responsive. ... Do you know whether the "dropped pulse" happens due to be a miss on an...
Hi all, It seems that my servos are going about 90 degrees under control of the servo module. But these servos will go a bit over 180 degrees under control of...
Hey Rich, We have a software upgrade for that board now which fixes both the problem with the range and the slight jitter you may have noticed. You'll need a ...
Hello, I have experienced xmax crush on quit. I guess that this is an unusual case, but I want to report just to make sure. This is a reproducible issue. 1)...
On June 19, David Williams wrote <snip> ... <snip> David, As a servo module user I received a reprogrammed pic and the servos now operate with much less jitter...
Hi Jean, (Is is Jean or Jean Marc?) Thanks for installing the new Servo software - I'm pleased it's working for you. The new servo software has a bigger pulse...
Hello David Williams, I also received an updated PIC, and it works fine for me (much less jitter). Thank you very much! ... I'm also interested in actual PWM...
What I do is start from the middle and go out to the edges until either the servo stops advancing or the servo motion gets erratic. Then record that position...
Hi Shigeru, The PWM on the MultiIO runs at approximately 40kHz. The Duty cycle varies between never on and continuously on in 256 discrete steps. When you...
David, Many thanks for your detailed answer to my question about new pulse ranges. I now have what I need to adjust my patch. All I need to do is to multiply...
Thanks, Jean Marc, We're very pleased with the fact that the Servo board has an on-board DC-DC converter. I can't believe the documentation doesn't crow about...
Hi List, The servos I'm using (Cirrus cs-60) are suddenly not responding at all to the Teleo module. All the LEDs are blinking as they should and the bound ...
Hi Jana, That is most likely to happen when I put the servos in the wrong way (done that twice). Is there a chance that that happened? Sometimes they seem to...
hi there, i`m currently looking around for hardware to control 16 servomotors. Teleo System seems to be a very nice alternative compared to my first idea of...
Hi Kiko, ... We think you will find Teleo gets you to your destination faster, and frees you to concentrate on whatever it is you are doing with 16 servos. ......
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
