hello Is is my first project with teleo. And i want to control a speed of a AC 200V/80W Fan. I made already some research about this but i have and i found...
Hi Filipe - unfortunately there aren't any MakingThings products that are very well suited to controlling the speed of an AC fan. You could turn the fan on and...
Hello Thanks for the answer Liam. I have a lot headaches searching for a solution. My fan have tree speeds and off. So my question now is if i need tree AC...
Hi, Be carefull to connect hobby-stuff to 200V devices. A relay could work but you are in danger of inadvertantly connecting the wrong way to the 200V power...
Hi list, I am trying to use a digital optical encoder, and the key is that I need to be able to tell which direction it is rotating. The encoder is very high...
"liam_lambo" said the following, but I could succesfully on iBook. ... Taneomi Uchida Waseda University...
taneomi@...
Sep 8, 2005 6:40 am
995
Hi Liam, Can you please provide some more details? Ideally, tell us the exact steps you took, and where and how it failed, and what error messages you got. ...
I downloaded the " XML Server & USB Driver " clicked to install it clicked the restart checked in the system profiler no drive went to the faqs page did what...
hi, is it possible to run 6 of yours Infrared Distance Measuring Sensor at the same time with the intro module? if not: what was the maximum amount of these...
It's fine now got it working Thank for help Liam ... ______________________________________________________ Click here to donate to the Hurricane Katrina...
With only 4 analog inputs on the Intro Module, you would really only be able to get continuous values from 4 distance measuring sensors. If you wanted more,...
You just need to connect the power supply directly to the sensors. This would require either buying a 5V regulated power supply, or using the Regulator Block...
So you're currently getting Din0 and Din1 readings, and you're wondering about how to interpret that information in Max to give you the direction? Or are you...
Hello all, I've been trying for weeks to figure out if the makers of Teleo offer an educational discount. I've already emailed Making Things several times...
Hi Noah - sorry your mails have not been answered promptly. Unfortunately, we do not currently offer a student discount. Our only discount is 10% off orders...
HI Liam, My Dad managed to successfully swap out the shorted H-Bridge, and got the motor module working again. But one again I blew it. Seems like neither the...
Teleo is a starter operation and doesnt offer educational discounts on a per customer basis. Generally hardware purchases dont get ed discounts. I am sure a...
Nathaniel - the way to limit the current on the board itself is to send a message in the 7th inlet (CurrentMax) setting the current beyond which the motor...
yeah basically, just that. I got the encoder hooked up right, but the software end is a little confusing. I had a really high resolution encoder (256cycles /...
FTDI has just released a new version of their USB Drivers for OS X. For those of you who have been experiencing some difficulties with the USB Drivers on OS...
Hi I just found two tilt sensors which I ordered from makingthings longer time ago with my teleo. I cannot find any description on how to wire them up. Could...
Hi, I've got a stepper motor block, and a polly block, and I'm trying to figure out now to set them up to my stepper motor to control a small sculpture. The...
Hi Nathaniel, I think there is a way (there may be others) Try this: Put the poly block in oscillator mode, adjust until it's running pretty slowly. Now the...
Thanks for that, I'm off for a few days, but I'll try that out as soon as I get back. In the mean time, any further suggestions appreciated. Nathaniel. PS,...
Hi Sebastian, Check out.. http://www.makingthings.com/products/acc_datasheets/acc_tlt_001.htm Although, note that the 1k resistors you have might not be too...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
