Hi all. Using Meshcam is it only possible to machine from the top down? or is it possible to machine up one side, change the B axis angle then down the other...
Although you may be able to come up with a way to achieve something like that it would be very difficult. Also, MeshCAM cannot calculate the offset of a...
Hi Robert. Thanks for the reply , If I go with your option of rotating the material, will Meshcam rotate the A axis with the use of a rotary table while...
Why is this spammer still here? ... -- Registered Massage Therapist Self-admitted Halloween Nut www.neilgillbanks.com [Non-text portions of this message have...
Hi Robert. Will Meshcam allow the A axis to be rotated parrel to the X approx. +/- 20 degrees? to allow cutter clearance for a 200mm deep cut.The material is...
Thanks for getting on it. The sad thing is it was probably a spoofed email address and the real Jim Sinclair doesn't even know he was spamming. Neil ... -- ...
I've run a few jobs single sided now and got some good results, but the next piece is double sided and I'm having trouble aligning the two sides :( Material is...
... sides :( OK - I've changed the tooling to inches. I normaly work metric, and the tools are 6mm and 3mm, but having been given a model in inches I was...
OK- I've just made it so all new members have to be approved by me. I'm not sure if this will help or not but I hope the situation will improve. -Robert...
The critical thing for 2-sided machining is to make sure the y dimension of the stock is accurately measured and specified when the toolpath is generated. If...
... That did not work. I've measured a 0.05" shift between sides, so I've shifted the bottom by that and it's looking much better. So why do I have a shift? --...
... Robert - I have a stack of 2.9" wide material (MDF) and have selected ones that are exactly that. The last two attempts I drilled a hole through the...
HI Robert, In your latest development blog entry you say "The next thing to write is a save routing that will save the image and the entire history so it can...
... Seconded I've a couple of jobs on the go and they are quite different, so being able to 'restore' the settings would be useful - typing them in again is a...
... write is a save routing that will save the image and the entire history so it can be regenerated." ... conventional sessions? My number 1 wish for Meshcam...
That's the second benefit of making all of the saved settings a script. It should be moderately easy after adding the scripting language to the MeshCAM core to...
From: "call_me_paco" <call_me_paco@...> ... It's the "News" link off the main page. I've asked Robert to post his new entries to this list, but he may...
... I'm missing something here :( This one is the best out of several I've machined, but still not quit right, the round section is still offset, making it a...
My reason for not posting them here is that I forget. I'll try to remember in the future. I wasn't really sure if anyone read the news link but I put the site...
Lester, I've been following your trials and understand . For most of the 2 sided stuff I do I have the luxury of designing the part so as to avoid critical ...
Even though I prefer Python I'm leaning toward Lua since it's so easy to embed and extend. From what I read the new Adobe program Lightroom is 40% Lua code. ...
Try setting your origin to the center west end of the block. Draw a line down the middle of the west end of the block and a line on your mounting plate. Bill ...
... That may be part of the problem. It looks like I was 0.02" out vertically, but I was expecting the part to be oval not offset if that was the case. Also I...
... That is were I am Bill - from attempt 4 on With a 3mm hole through the block exactly on the center line and I'm dropping the cutter directly into that hole...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
