This is the interrupt service routine (ISR). You place inside the function what you want done when an interrupt occurs (in this case, Timer0 interrupt). You...
We are a Japanese IT Company engaged in Software Development and located at the UP-Ayala Technology Park in Diliman, Quezon City. We are looking for motivated...
tanong ko lang po kung paano magprogram sa encore na gumagamit ng Analog to digital conversion na tumatanggap ng negative input voltage. wala pa po kasi ako...
gud day! i just like to ask if this a valid format in implementing ... when i simulate the code, it processes only the condition (event = FRONT) & (behavior =...
thanks for replying to my inquiry. i'll try out the function to see what happens. i have another problem here and i think it doesn't look really good. i was...
it cannot accept a negative voltage. look for a book on op-amp circuit design. suppose you want to digitize a voltage from -10v to +10v. you need to design an...
I'm not sure if encore accepts negative voltage inputs, but I think they're not. I suggest adding DC offset to the input analog signal. I think you could...
Z8 Encore! Interface Driver, Version 4.9.6 Copyright (C) 2005, ZiLOG Inc. All Rights Reserved CPU Z8F6421 Rev BA, Target=Z8F64200100KIT - SERIAL, On Chip...
If you want a quick fix.. try restarting everything. poweroff-poweron (including the chip). Unplug then plug communication ports (you may also want to try...
i tried everything you said but it's still not working. i even retyped and ran the code to a different computer. i also tried downloading other codes that i...
FSTAT is actually read-only. Have you tried downloading to another chip? or board? It may be the uC board that is causing the error. (Hardware problem)...
i was able to download the code to another module and it ran although the program is not that perfect yet. i already suspected that the hardware part must be...
download the latest zds2 software version 4.9.6 at zilog.com this should fix your problem. ive encountered this problem before version 4.9.6 is more robust and...
i'm already using the latest zds2 software v4.9.6 but i'm still having this problem. before i wasn't having this problem until now even though i have the...
what development kit r u using what z8encore chip? is your board your design home made? did you made your own debug board? check for connectivity of your...
i'm using a Z8F6421PM020SC chip and the module i'm using is home made. i only have one version of zds installed in my pc. i checked everything and they all...
i'm using a Z8F6421PM020SC chip and the board i'm using is just home made. i tested the board with another chip and it is working just fine however when i...
you might want to review your board design to avoid possibly damaging another chip. try isolating the source of the damage and redesign the board if necessary....
ok i'll do that. i'll review everything and find the cause of the problem. thanks again for the help. Melvin James Faeldon <jafaeldon@...> wrote: you...
definitely your home made board is working properly. i think you should check the setting of your zds II. make sure that the zds is set to communicate w/...
thank you sir sison for the response.....ask ko din po kung may possibility po ba na maibaba sa 8-bits lang ang 10-bits na ADC? binabalak ko po kc na 8-bits...
limit your input to +/-1volt, then your analog negative supply connected to dc ground ng digital circuit, ang output ng analog circuit mo na zero magiging 1...
sir, palinaw naman po, hindi ko po maintindihan.............ung analog negative supply connected to dc ground ng digital circuit, ano po ung tinutukoy ninyo...
di ba may sariling supply yung analog circuit mo, (+) , GND, (-)? yung negative supply ang ikonek sa dc ground ng digital circuit. yung output naman ilimit mo...
We have a pic16f877 controlling 16 latches(74373). The output of the latches are connected to LEDs. The output enable of the latches are connected to ground...
good day to everyone....sinusubukan ko po mag-interface ng pda at encore na z8f6421. sinubukan ko muna po gumawa ng dummy program na magpapadala sa encore ng...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
