Hi! The Advanced Science and Technology Institute (ASTI), an attached institute of the Department of Science and Technology (DOST), is in need of the...
The Institute of Electrical and Electronics Engineers, Inc. is pleased to announce and invite you to the launching of the Microcontroller Applications Design...
... pleased to announce and invite ... on 9 July 2008, 2:00pm at the World Trade Center. ... (Line-Following) ... students to participate. MADC 2009 will also...
Good day. I'm Mark Anthony antonio from pamantasan ng lungsod ng maynila. We're very sad that we didn't attend the madc 2009 launch because our excuse letter...
You're invited to join Limuel Jeff Sinel's network of friends. By joining Friendster, you can reconnect with old friends, meet new friends, start a blog, build...
We are in need of the following: We may also consider hiring fresh graduates who were active in the MADC programs and have exposure to Zilog applications and...
Carolina Marrero
cmarrero@...
Jul 24, 2008 8:37 am
2237
feedmelink.com is your gateway to sites on the internet for Technology!browse our resources or just try the search http://feedmelink.com/...
You're invited to join Limuel Jeff Sinel's network of friends. By joining Friendster, you can reconnect with old friends, meet new friends, start a blog, build...
You're invited to join Limuel Jeff Sinel's network of friends. By joining Friendster, you can reconnect with old friends, meet new friends, start a blog, build...
Gud day. anyone knows where to buy high speed, high torque dc motors? i would be using that along with zilog microcontroller for my project. id be so thankful...
me too i am looking for that DC motors... please help us.. i will also use that to my zilog project. making my line follower robots. ... From: ronnievicente_06...
tama e-gizmo nga madami. tpos kung line follower try nyo din sa tamiya/futaba. daming dc motors dun, kung torque naman problema mkukuha sa gears yun. Franz...
Good day. I have a project regarding long range RFID. can anyone help me where to buy the sensors and cards for the said application> thanks Dan Magcuyao ...
Thanks. I have tried looking at the e-gizmo, pero passive pa langyung RFID nila eh,,, yung kailangan itap yung card sa sensor. I want sana yung like of the...
good day!!! we are currently working with a project using z8 encore microcontroller our problem is that we lack of the GPIO ports needed to accomplish the...
regarding 2 uarts, yes u can do that. just connect Rx1 to tx2 and rx2 to tx1 if i can suggest an alternative, why not use a shift register? or a multiplexer to...
tnx...we are also looking ways to increase the gpio pins and one of that is to use multiplexer... regarding the uarts can i directly connect the two uarts???...
yes u can, make sure both mcu's are using the same voltage level or from the same source to be safe. then have their grounds in common. and of course, the uart...
thanks for info and i already went to look sa gizmo but what im lookin for is a high speed motor at the same time with a high torque. meron daw po xe cla don...
yes. you can directly connect UARTs between 2 MCUs  if you need more I/Os, i suggest that you get a ZNEO. it is 16-bit microcontroller from zilog also. it is...
for the availability of ZNEO, check digikey or mouser. To: microdesigncontest@...: microlan2002@...: Mon, 4 Aug 2008 18:25:18...
lailan de padua
microlan9@...
Aug 5, 2008 1:29 am
2255
have you ever played with tamiya? I mean fully-cowled 4WD tamiyas.. There are lots of dc motors to choose from. But if you're looking for a high-speed,...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
