Hallo..., Very interesting software,Thanks. However we need some examples or real case. It is very nice when someone can share they projects under Homer...
Thank You For Sharing HOMER: I Too could use some examples of it's use on Hydro applications only. It seems to be more slanted toward PV, WIND and Diesel...
Hello Don, Now i understand your real world ! Your battery pack is your regulator, if is big enough, you don't need a dump load (that why your dump load don't...
Bob: Thank very much for your message. Indeed good place to start searching. Also, thank to those that added messages to the initial message Nando ... From:...
nando
nando37@...
Apr 2, 2008 4:42 am
9541
Thanks, Eric; I don't think I did have a question, I'm trying to ask "Why doesn't more of the world do things like I did in my system?" It works flawlessly on...
Hi Don, Woo Hoo! Are you saying you are running your 3-phase system off of a floating paddle wheel? If this is so, you sound like the man I should be paying...
So far I am using a 5' overshot wheel. The floating one (undershot wheel) is made but not installed yet, we have had an incredably snowy winter here and my...
hello thank you for your replies. we tried to do everyhthing you said, but we still cant get anywhere near the theoritical output. 1. we drove the motor to...
Have you tried a different induction motor unit from the one you are currently using? Roberto ... From: spicycrab00 spicycrab00@... Date: Thu, 03 Apr...
rverzola@...
Apr 3, 2008 9:16 am
9547
Hello Spicycrab00, I didn't understood exactly your description of how you intend to make 10 uF, but please note that if you put 2 pcs. of 5uF capacitors in...
Sherwin, I'm sure you have this correct, but I am wondering about the capacitor connections. To derive 12.5uf, a series - parallel connection is required with...
Note that if you put capacitors in series the capacitance drops. That is two 10 MFD capacitors in series gives 5 MFD while two 10 MFD capacitors in parallel...
Hi: Shouldn't The Cap's be in Parallel not series to add the capacitance together? our circuit is C-2C, but for the C we used a combination of 3 capacitors,...
i am from Pakistan. We don't have any security devices inatalled to our units. i have one 20kw unit running while other unit of 20 kw is under process and will...
When you have better security devices installed, how about using your extra electricity to overcharge an enclosed battery bank of lead-acid deep cycle...
Hello, sorry everyone for the confusion. i typed it wrong, the Capacitors in fact were all in PARALLEL,and not in series, we are actually using "20uF for C"...
Notice To Group: This response is a "cleaned up" response, as requested by the group moderator. Dump loads are easy enough, just use any electric-water heater...
... various of specific speed. ... doesn't more of the world do things like I did in my system?" It works flawlessly on 3-phase generation with industrial...
... various of specific speed. ... REPLY: if u can send me your postal adds i will send u complete set of designs of Turbine blades and spacings and diameter...
I need quick advice. I am working on low head propeller turbine U=predicted 500 rpm, Pnetto= 500W. On ebay someone is selling PM generator. Can be usefull for...
Marko: You have not indicated what the load is. The 3 phase brushless unit is a 4 KW and you have 500 watts, it may work but may have a loss of some extra...
nando
nando37@...
Apr 4, 2008 11:20 pm
9561
Further on this If 1000 RPM it seems that the generator produces 89 volts with a 500w/220 v = 2.27 amps ( value is much lower since it is an incandescent lamp)...
nando
nando37@...
Apr 5, 2008 4:16 am
9562
Hi Nando, Nice to have an expert opinion. I forgot to write that I am not expert of electric machines. If mentioned generator truly works only at higher rpm I...
Hi Nando I tried to send you the ladder logic diagram and the following message to your email address, but it has bounced back to me, so I must have something ...
Please unsubscrib my email from this group thanks ... Kunjungi halaman depan Yahoo! Indonesia yang baru! [Non-text portions of this message have been removed]...
Sabar Nababan
sbr.nbbn@...
Apr 6, 2008 4:27 pm
9565
dear all, the site data is H net= 154 ft, Q= 560 lit/sec and penstock dia = 20 inches and Length =1750 ft . what should be th pipe thicknessif its mild...
SABAR: Unsubscribe your self, read the bottom of this message, carefully and do the proper steps. Nando ... From: Sabar Nababan To: microhydro@yahoogroups.com ...
nando
nando37@...
Apr 6, 2008 7:04 pm
9567
Shabab Schedule 20, 18" diameter should be adequate for both pressure and flow velocity. The cross flow is a difficult unit to control at that output. A...
Tom Spicher
hydroyes@...
Apr 6, 2008 7:54 pm
9568
I only wonder about this idea: I wonder why the opening underneath the water at the dam is not covered with a rectangle larger than the opening, made out of...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
