tetragramatonah, I will proved some comments. two magnets of the same polarity. take a clear plastic tube place a disc shape magnet in the tube of a diameter...
David, I'm a little confused by your response. The float between the two magnets composing the piston would keep this levation from accuring. For levatation...
Found a youtube video that has a full spiral of outer magnets setup with a spinning rotor on it's side using a bindini circuit to kick the rotor past the...
Jay, Let me clearify a little, I believe the concept has a potential of success. But not in the present configuration. As the noodle float rises it will...
I think I understand a little better what you are talking about.... I was thinking that the weight of the piston would be great enough to make one end heavier...
Jay, many of the same thoughts I had when trying to overcome the problems I also liked the spiral arrangment. I have done much of my work based on the TOMI...
Jay, Though the system design may have difficulties the concept of a bouyancy mechanism offers a new road of potential to be explored. I'll explain latter...
Could there be a way to set up a resonating compression wave in the fluid of the bouyancy device such that its oscillations will occur in phase with the cycle...
6231
minatowheel@yahoogrou...
Nov 2, 2011 9:09 am
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the minatowheel group. File : /BPPMM.gif ...
David, I uploaded a quick gif animation to diagram the new changes based on your input. The red line on the magnet diagrams are to designate the north facing...
Great drawing annimation. The trick will be to get the boyancy power sufficient to overpower the magnet attraction down at 7-6 oclock.... In all of my magnet...
Jay, now this is what I would call waltzing matilda down at the billabong. and it is not too much more complex than the original. Getting Norman to comment...
Thanks for the kudos on the animation Norman! I guess all the years jacking with adobe photoshop has paid off(trick in creating fast animations in photoshop...
Jay,  I'll keep an eye on the posts. The TOMI is far less complicated than you may think once your in the track it should move to the end this is where it...
Just ran into a problem. Spoke with a Mechanical Engineer friend of mine who works with fluid dynamics... Basicly he told me that water or any liquid/gas used...
Searched all over the place to try and find any info on the crap my friend told me.... found nothing helpfull with buoyancy using a vacuum medium, in fact...
6239
minatowheel@yahoogrou...
Nov 3, 2011 7:21 am
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the minatowheel group. File :...
Added an animation with added bump hindges attached to the 3 south in facing magnets the black dot shows place of supposed axel hindge and the plastic yellow...
I figured out what my friend was trying to tell me. The displaced water is also displacing the air around it as the piston moves through displacing it and...
In the discription for the lung I forgot to mention the weighted ball valves at the ends of the tubes inside the rotor chamber that would block water flowing...
Jay, Did you check out what you were told? The problem is the use of the word PISTON suggesting a tightly fitting float. Take your piston float and make...
David, Thanks for anther view of the pressure issue that was described to me. My friend got a little technical and confused the hell out of me with the wave...
Ok, so I went out an purchased a 1.5 inch by 5 foot long schedule 40 PVC pipe. Cut them into 4 equal 15 inch lengths, weighed them and they're all 288 grams...
I've created a folder named BPPMM and moved all the files I've made so far into that, so things don't get strung out everywhere. I've also uploaded a picture...
I've created a folder named BPPMM and moved all the files I've made so far into that, so things don't get strung out everywhere. I've also uploaded a picture...
Hi Jay I havn't been on minato wheel for a while so this is the first time I have seen your idea, are they same pole magnets facing each other on the stator...
One more thing I don't think gravity will play a big part in your design but there is also another weak force that will play a part and thats water repultion,...
Hi Jay Sounds cool mate I will be waiting to see how things pan out, I hope it works out and all that layout of money is worth it. Take Care Jay Graham...
