Hi Mark. If DXF is the output, what format is the input? Thanks, Eric. ... From: Mark Hayton To: minatowheel@yahoogroups.com Sent: Saturday, July 31, 2004 6:53...
Hi. Is it possible for me to get those functions? My Wheel drawing program is in VB and a button for: create DXF file should be very nice beside the button: ...
Hi Norman. Perhaps several replications can be made by different persons. It can be like the 'lifter'-project. When I come home from holiday I like to build...
hi groups, since you guys are the experts in magnets:D i thought you might appreciate this idea, and be able to help,this is form your other nemisis of wheel...
1) the magnets and the drive rods thay are mounted on are the only things that turn in thie view,( a view from the backside would show all the drive rodes kept...
guys what do you think? http://my.voyager.net/~jrrandall/Misc/GordyManyMags.gif -- In minatowheel@yahoogroups.com, "ashtweth_nihilistic" ... bowman ... sink. ...
Hi, I'm new here so hello everyone! :-) I'm also new to this field and don't want to reinvent the wheel... as it were ;-). I've been searching through the...
After viewing the animation, I would conclude that since attraction is greater than repulsion, the point of equilibrium would be when the inner circle of...
Hi, I had an idea but It depends on one thing I'm not sure of... imagine the following: You have a pencil held upright, and put two wheel magnets on it so...
Hi Anthony I would feel the magnetic field would have weight because its made up of atoms so it has mass and if it has mass it must have weight, I could be...
This is in response to your message, echoed below this reply... Without actually doing the experiment, I tend to the view that there would be no difference in...
Hi Anthony, welcome to the world of magnetic intrique, several attempts to utilize various forms of your idea are what its all about if I remember correctly...
After studying this for 2 weeks I now have measured that the 4 washers do not weigh 4 washers so the 400% OU is not valid. see this for the details. ...
Hello All, I'm finally back from my out of town trips and boy do I have a lot to share with you all! I just e-mailed Eric about this last night so instead of...
I am just finishing my program to computer generate a 3 rotor design and output DXF files so I can send then to be cut. But your animations look just about...
Oops, the links I added got messed up. Here's a listing of where all the pictures are in the files section: Files Section - Repulsion Motor - Offset...
Hello All, I finally uploaded to my album the pictures of my spiral motor prototype that I was talking about a while ago. I also included some pictures of a ...
... Jason- Tri-phase, as I understand it, means using the combined forces of three rotors slightly out of phase with one another in order to overcome the ...
Hi Jared, You're exactly right about the definition. The only thing I'd say is that the size of the magnets may only be a factor depending on the type of...
Hi Mark, I'm glad to hear you're making progress and thanks for the comment. I actually just recently finished a small program that can create different...
... Jason, I think you're on the right track here, most definitely. I like the notion of having all three phases on the same rotor, instead of having to add...
Hi Jared, Actually, I have been thinking about how I could build a simple prototype that can be tested and possibly even adjusted to get the offsets just...
Jason, I think you're on the right track. Instead of using a piece that's 3/4" thick though, you could get three pieces each 1/4" thick, and cut a set of slits...
Hi Jared, That’s a great idea! I wonder why I didn’t think of that before! Making slits as opposed to holes will not only make it easier and more accurate ...
Hello again Jason, It sounds to me like you're one step ahead of me but we're both on the same page. Your program that makes wheels of defined dimensions could...
2005
MILEHIGH3D@...
Aug 15, 2004 5:33 pm
hello group- Though I have not written much, i am following your efforts closely. Would you please send which parts of the website have this information...
I am so close with my program that I will just finish it. Thank for the offer though. I should also be able to create a 3D DXF model once I get done. Anyone...
Hi Jared, I'm thinking exactly the same thing as you as far as the bike idea goes. That was actually the very first useful application that I have been hoping...
I finally figured out all the math to get my rotor design program working. I turns out that I had to dynamically scale the radius until it fit the given magnet...
