On Thu, 01 Sep 2005 01:41:10 +0000 ... I doubt it because using the steel gives the off/on possibilities whereas permanent magnets are always on. That is why...
Hi Norman I agree about the off and on but I also know that when both pieces of steel are in the magnetic field they are magnetized, the difference between the...
This is a curious offering. If you look under "mosaics", it almost has a Bedini feel to it: http://v3.espacenet.com/textdoc?DB=EPODOC&IDX=EP1569322&F=0 Paul....
Hi. Did someone in this group investigate the Bill Muller Generator? Searches on the Internet do not give all details. Does someone have more information ...
Eric, Are you interested in his earlier design that was called a high frequency Motor-Generator or his later attempts. I ask this as I have hard copies of...
Thanks Mark. That was a good place too start. Eric. ... From: Mark Hayton To: minatowheel@yahoogroups.com Sent: Saturday, September 03, 2005 10:30 PM Subject:...
Hello Ralph. I guess that his latest device was his best device and that his earlier attempts were devices under development. But I can be wrong here. It will...
hey all amorphous polycrystalline , who knows that material and can give me some technical inside. How strong is the material when it becomes a magnet. Is the...
Hi Eric, I have had the pleasure of meeting Bill Muller, and having him demonstrate his device, befor he died. It appeared to work just as he said, and he had...
Hi John, Bill used black sand that he collected from the beaches in Penticton, BC, and cleaned with a magnet. This was mixed with fibreglas resin and molded or...
Wow! I did a Google web search for amorphous polycrystalline and got so many hits I would be here all night copy and pasting them. Do a Google search and you...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the minatowheel group. File :...
minatowheel@yahoogrou...
Sep 5, 2005 8:45 am
3428
Hi All I just posted a drawing of a theory I had for a magnetic piston, I would like your input because I can't see why this would not work. In this there are...
hey all, Gerry you have seen yhe muller device? My question is, have you turn the rotor by hand trough the stator. If you did , whas it easy or not? the magnet...
Yes, I have seen it. I have measured the input and output myself. I have turned it by hand and there is no cogging effect. I have held a short curcuited coil...
On Mon, 05 Sep 2005 00:32:26 -0700 ... The serach is independent of the internet connection because all you do is send two words up to the search engine. Those...
Hello Gerry. I found that a lot of the information about the Muller Generator is a bit old. When did you meet him. Are the pictures at www.mullerpower.com from...
Graham, Great job! If you are not familiar with a Stirling engine, you should check out how your design could work for moving the "displacer" in "Gamma...
I met him in May, 2003 as I recall. The pics on the mullerwebsite are the unit I saw. I have heard of others making successful replications, but they said they...
Thanks Gerry. That switching is a part that is not completely given on the internet. I found on an older blueprint a part called: decoder wheel. I guess that...
Bill had used an optical switch unit and was dissatisfied with it. He used MOSFETS triggered by Hall sensors, which had to be adjustable to maximize timing for...
hey gerry, thank you for answering all questions. there are things more clearly now already for me. but like frequently a question comes with each answer. now...
John. The web site www.mullerpower.com, by Bill daughter Carmen, is going to publicize more facts about the last machines. For a successful replication the...
hey all, thx eric . to see more is helpfull on the things i have found the basic's are the same on all that models , eric that from the magnets, that they are...
Yes, I have seen those bar magnets as well. I placed a picture at http://www.fdp.nu/shared/files/Bill%20Muller//Muller%20HFG.jpg Regards, Eric. ... From:...
Hi James No I have not see the stirling engine, having said that the stirling engine need an outside energy source in heat and my idea has always been to have...
I have seen and handled the magnets, but the assembled rotor has a stainless steel cover on it, and the posting by Eric of his drawing I think, would be the...
... To Keith Hollyfield, Please be advised that I have sent copies of all three 1987 drawings to Eric. If he can do so I am sure he will soon be posting them...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
