Hi all. I don't want to sound like an old lady, but please put on gloves when handling those flat Neo's. And keep them out of the way from your children. Again...
On Mon, 02 Jan 2006 19:32:33 +0100 ... I second that. I spent 20 minutes gettime 12 of them apart and safely located on a metal plate with distance between...
Hi All Yes I would have to agree with Eric also, them neos do hurt when they snap together with your skin between them so safety should be your first thought. ...
Hi Norman Yes I have had two and three CG's work, I have videos in Erics file section of his site showing 2 and 3 CG's but if you mean joining them together...
Thanks, I have a problem with abbreviations for newcommers so I like to spell CG out. First I want to try putting a bar matnet above and another below but...
On Tue, 03 Jan 2006 10:06:29 -0800 (PST) ... Attachements are not allowed and get dropped. You will have to upload them. How many degrees does it rotate? ...
The minatowheel yahoo group is all but full. The pic I tried to send was simply my C-Gates that I had built. I have done the same thing as Erik with a simple...
Hi Mark That was a good question, I would like to know the answer to that myself as far as I know 4 people have replicated the CG and two of them 4 have made a...
Hi. Adding a second gate, in opposite of the first gate, made the device stop working. I think that gates have to be added on different height levels. With...
Hi Graham. You should count me as Sweden, rather then Holland. Eric. ... From: Graham To: minatowheel@yahoogroups.com Sent: Tuesday, January 03, 2006 10:24 PM ...
I just ripped apart an old harddrive last night so now I have a nice rotor with stand ready to use for my CG testing. If no one from the US has verified the CG...
Mark, Did you remember to remove the neo magnets from the drive? Probably a stupid question, but they would sure mess up the fields. James ... From: Mark...
Yes, I stripped it all down to nothing, the only think left 1/2 of the case that holds te bearing and the shaft and drive platters.. It looks like it will work...
Hi Graham, You can make that two for canada, if you like. I had tried it before and couldn't get it to work with my magnets. But you shamed me into trying...
Hi Eric Sorry about that mate I assumed being the dutchman you was from Holland but we all know what happens when people ass_u_me. Take Care Eric Graham ... of...
Hi Ron Thanks for your comments Ron I appreciate that mate and bummer the Canada's are ontop now hahaha looks like the US is losing a bit of pride here, it...
Works in Indiana as well. Noticed a couple of things. The rotor magnet seems to need to be at least 3 inches long. Stacking cylinder magnets together works....
Eric, Graham, and All, For the U.S.A., I can confirm the Clarke Corner Gate works as shown in Graham's videos, BOTH for NIBs (neodymium, Iron, Boron) which you...
Hi Nick Its good to hear from you mate and its good to hear that the states are on the board. Take Care Nick and thanks for your participation it truly...
Hi Tom Its good to hear you got it going but the canadians well be disapointed that the states have court up but then again I do expect them to go way past...
Email me the photo and I will post it elsewhere. My setup is not very good. The bar magnet is 2 1/2 inch by 1/2 inch by 3/16 inch thick. And the Corner 1x1 x...
On Wed, 04 Jan 2006 00:52:36 +0000 ... Then is the 5 inches the radius from center axis out to arc or is the 5 inches the diameter of the arc circle. I am only...
Hi Dan and All LOL I thought the States would come through I just wanted to give them a kick as it was but I would think the poms are lacking abit and that's...
Hi Norman That would proberly be a 5" radius giving you 2 and a 1/2" ever side, I think the problem with smaller magnets is the turning circle is tighter so...
On Wed, 04 Jan 2006 02:22:37 +0000 ... I did and its no better but when I put two in sequence about 80 degrees apart there is a constant pull thru from one to...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
