Hi Mark, That is definately significant! But I suggest that you try the pendulum test with and without the shielding you are using so you will have a control...
But if you have a one-way gate, there will not be more than one swing since it will not be able to go through the gate backwards. So I gues it is not worth...
If I don't have the shields on, the pendulum arm wont even make it to the other botton of the swing, the repulsion will be too strong to allow the magnets to...
hi every one, Here i have attached the picture of the CAD model of the Magnetic repulsive engine. Just now i finished constructing the cad model. I planned to...
hi, As u could see in the picture i have used two magnets one a half ring magnet mounted on the wheel. the other is a rectangular magnet which slides on a...
Hi Vinay. Could you please add any files and photos you have to the files section. We cannot recieve file attachments directly to the group. God Bless, Jason O...
hi, i have created new photo album "magnetic repulsive engine" in the photos of our group. The picture is uploaded to it. you can view it there. vinay Jason...
The test is usefull but one must be careful when makig conclusions. Since the test is very basic, gravity can enter the experiment as an unwanted 'help'. Eric....
Hi Vinay. Do you have this picture in CAD format? I would like to look at it in 3D. I use SolidWorks but if you use something else perhaps you can export to a...
Hi eric, I too use solidworks, I have uploaded it to the groups. Take care Vinay Eric Vogels <eric.vogels@...> wrote: Hi Vinay. Do you have this picture...
Hi. I found the folder, but no files there. I made free space. Please try uploading again. Thanks. Eric. ... From: vinay v To: minatowheel@yahoogroups.com ...
Thanks, I found the file now. Unfortunately I'm using SolidWorks 2003 and you have a newer version that is not recognized by mine. Another export format should...
I have exported to ,crg format hope you can view this, but i think you may not able to view the simulation of the model. Try this out.... Take care, Vinay Eric...
Thanks. You are right: I cannot do the simulation but I can look in 3D. I like the design. I'm not sure if only one unit will work bet perhaps some units with...
Hi, How to cut the ferrite magnets. I have to cut my Ring magnet inot half to fix it to thee wheel. vinay Eric Vogels <eric.vogels@...> wrote: Thanks....
Hi, How to cut ferrite magnets. I have to cut my Ring magnet into half to fix it to the wheel. vinay Eric Vogels <eric.vogels@...> wrote: Thanks. You are...
There are cutting wheels for the Dremel and RotoZip tools that can cut it. You will need the cutter to be very thin so you don't lose allot of material from...
You may use a tile saw with a diamond blade if you have one. Using it "wet" will also prevent heat which can kill a magnet. James ... From: vinay v To:...
ok thanks mark, I will try grinding them regards vinay Mark Hayton <mark_hayton@...> wrote: There are cutting wheels for the Dremel and RotoZip tools...
Ok Mark, I Will grind and let you know. Vinay Mark Hayton <mark_hayton@...> wrote: Make sure to Wet Grind them so they don't heat up and start to lose...
... Its a bit lo-tech but works: get a tungsten carbide blade for your hacksaw, and play Bob Seger and the Silver Bullet band through headphones to keep your ...
Hi everyone, Finally i made it into halves by using a hacksaw. I used highspeed steel blade. but it took me 2 hours to cut it. Vinay ... Its a bit lo-tech but...
I just bought over 600 pieces (0.5 pounds) of Magnetic Metals Inc., #2425EE4914 SuperPerm 49 - Plates both E and F from old high end audio transformers....
Thanks, I have a sheet of Magnet-Shield and Joint-Shield and I am going to make layered shields, like they recommend. I am asking them for the information I...
Hi Guys. Since nobody replied to an earlier mail I will do that myself. I'm not sure if the mentioned device passed by everyone's attention but it is really...
Hi Eric, Sorry I didn't reply to you about this much earlier. But yes, I started the post on the Walter Torbay motor after getting a tip from Dan LaRochelle....
Hi Jason. When I was reading through the 600 posts yesterday, to catch up, I read that you in the beginning of the thread already pointed out what the real...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
