Hi all. I just made Trevor a member in this group. On his request I added his email address to the list. If everything works as it should, he'll receive this...
Hi all. I cleaned my guest book from the discussion about Trevor's engine. Here is all the material listed. I also added the 2 pictures he made. Regards, Eric....
Hi all. Do you remember the "Working Device" from Mikell that was launched some months ago? I collected all information I could find from the Internet and put...
Hi to everybody! My nakme is Salvatore and write from Italy! I make excuses myself for the English bad one. I wanted only to know whether someone of you was...
Hi Salvatore. I did not manage to build a self-runner yet. I obtained better results while using wheels with more then one track of magnets. And until I tilted...
Hi Eric This is Graham Clarke again I had a theory about your runner and gate I know it will push it around and I know it will stop if it is closed and if you...
Hi all. The following link is to a home made Gaussmeter. http://my.execpc.com/~rhoadley/magmeter.htm Perhaps Darren can look at the schematic. I planned to use...
Hi Eric. I have wanted to build a gaussmeter too for some time now. I even bought the calibrated A3516 device for my project. However, as you have observed, it...
Thanks Darren. In my case I only need to compare a handful of NEO and find those with EXACTLY the same force. I guess this will work with the 'spacer' idea. ...
Hi all. On the last day of the year I added a animation of the Bowman Permanent Magnet motor to my site at http://fdp.nu/bm-movie/default.html The device could...
... My problem with this idea that came from the Peregrinus wheels is that the magnets are on the circumference pointing out but in holes of the wheels...
Hi. I think it is a matter of balancing. Balancing by moving the smaller rotors closer (at the repelling side) or further away (at the attracting side) so that...
Hi all! He will not work for me. According to my opinion all the strengths will strech advertising agents balancing him, and not us will be no rotation. Robert...
Hi all! He will not work for me. According to my opinion all the strengths will strech advertising agents balancing him, and not us will be no rotation. Robert...
Hi Salvatore. Thanks. I applied for a membership in that group but I'm not yet accepted. Could you please send me the pictures already? Thanks. Eric. ... "Are...
Hi all. I made the 6$ gauss meter. Since I had a digital voltmeter, it was only a little bit more then 6 $ (Sweden is NOT a country for R&D). It's great to ...
Eric, I would suggest that you build the "slightly more expensive" version of the meter, but use the last opamp in the quad package as a comparator, fed from ...
Thanks Darren. For now I go for the comparator. Since I'm at this moment (my Bowman project) not really looking for gauss, only for comparing magnets with each...
Hi Darren. I have some problems too find a suitable comparator circuit. Do I understand it right that I need three of them in order to find out if a voltage is...
Hi all. I became member in the egroup of Robert Calloway. At the moment the discussion is about a test that can be done with the attached wheel. In case ...
Hi all. I made a video clip of my Gauss meter prototype. I added a circuit that Darren Kozey (thanks Darren) designed that shows North and South pole with a ...
Hi. I use Microsoft MPEG-4. And Windows Media Player 6.4 (on W2K) Eric. ... From: "Mark Hayton" <mark_hayton@...> To: <minatowheel@yahoogroups.com> ...
Hi Eric nice job on your CKT, which Hall Effect did you use. Its nice to have a visual led and a voltage gauss reading. I did notice a real differance between...
Hi Wayne, I used the A 3515 LUA. It's not calibrated but works fine for me. Since the Hall to not too sensitive I need a distance between magnet and sensor....
Hi Eric, Could you print out the ( Kozey) red-blue light circuit for the gaussmeter and E mail me a diagram? Parts list also. I finally got my hall effect...
Hi all. For those who want to build the Gauss meter with the pole detector I have put the circuit at ...
563
MILEHIGH3D@...
Jan 14, 2004 11:14 pm
Hello Group- Please look at the latest "Nexus" magazine. It shows what may be how to make a magnetic monopole in article about new type of electric motor...
564
MILEHIGH3D@...
Jan 14, 2004 11:16 pm
Check out this site- http://www.flynnresearch.net/rotary_motors.htm -Miles...
