Hi All, Please check out the Pendulum/Magnet device in the photo section. I am building this at present and open for input. I have been working with large ring...
2 hours at 250 degrees Celsius in a normal oven was not removing the magnetism. After 20 minutes in a wood-burning stove the magnet cracked. Eric. ... From:...
... magnetism. ... Hi Eric, The Curie temperature of ferrite/ceramic magnets starts from 400-450 degree Celsius and usually even higher. So 250 Deg. C is a bit...
... Surely the standard method is to place the magnet in a coil, or wind a coil around the magent, apply an alternating current, and gradually reduce the...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the minatowheel group. File :...
minatowheel@yahoogrou...
Apr 8, 2007 4:17 pm
5405
I made some progress with building. Although not many people are positive about this device, I think it gets better and better every time I come a little step...
- Hi Tom: You mentioned in the photo file that you are concerned about getting the timing of the magnet runner correct. It this system is workable (It looks...
Oooops! I just realised I saw an almost identical device to this at www.besslerwheel.com It was deciced it would not work. Look at it this way. As the tip...
... http://www.geocities.com/geoffegel_99/garymotor.htm This motor did work. ... positive about this device, I think it gets better and better every time I...
... swing ... too ... it ... Hi Trevor, You just might be right about your ideas. I have been thinking about what you said for some time and have come up with...
I realise that this is very off-topic but I just have to write that I finally can do with my CNC mill where I have it for. I needed some parts for my device: I...
Under the simulation is a photo that shows the progress of the Dual Piston project. I still feel positive about it. http://fdp.nu/dualpistondevice/default.asp ...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the minatowheel group. File : /Magnet...
minatowheel@yahoogrou...
Apr 19, 2007 6:04 pm
5413
Hi, In the files section I have posted a movie clip showing the Mag-Gen motor idea I am currently building. I am constructing another ring that I am holding....
Status: All levers and bearings are installed. I have the movement I want. Now I have to add a slider bearing to the shield. One slider bearing at the bottom...
Hello. Does someone have experience with Carbon Fiber? I wonder if it is a material one can use as a hobbyist, or does it need very special equipment? My...
Eric Carbon fiber and graphite rods are excellent building material. I have used square graphite rod in many of my projects including my latest "Sotropa Motor"...
Eric, If your looking to purchase Carbon Fiber, Most of your Remote Control Hobby shops carry the stuff in Rods, Tubes & strips. It bonds well w/ CA glue or...
Eric I order mine from here http://www.toddsmodels.com/ and easy to cut and use CA glue. There is most likely a place on your side. Strong and light weight ...
There are two main types: "Wet carbon", which is what you usually see for aftermarket car parts. It has a glossy finish from a clear coat or the epoxy resin...
Have you tried searching for DIY carbon fiber? There are tutorials out there for working with wet carbon. There are places on eBay that sell rolls of carbon...
Thanks for the advices. I'm now searching for a Swedish supplier since I don't want to buy liquids overseas. It will be interesting to see if I can form the...
Believe it or not, we actually spell it "fiber" in America. But everyone thinks British accent are hot, so we'll use "fibre" when we're talking to the ladies....
I've recently joined this list, so hello to everyone! How are your projects progressing? Have any of you gotten more than one revolution without "pumping" or...
... Google should create a table of equivalents. At the moment, you do not get the same pages being reported. I think the use of uppercase OR would work: i.e....
Hi Daniel. Considered, yes. Done, no. It are all plans on my miles long ToDo list. During my experiments, more or less pumping has always been the key for...
Hi Daniel I agree with Eric the only way to make a permanent magnet motor is with some kind of pulsing, if a magnet can be pulsed up and down using the energy...
An update: I tried my first shield and I discovered two things: 1. My shield was mounted too low. It went down too much and the magnets repelled where they...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
