Hi all! He will not work for me. According to my opinion all the strengths will strech advertising agents balancing him, and not us will be no rotation. Robert...
Hi all! He will not work for me. According to my opinion all the strengths will strech advertising agents balancing him, and not us will be no rotation. Robert...
Hi Salvatore. Thanks. I applied for a membership in that group but I'm not yet accepted. Could you please send me the pictures already? Thanks. Eric. ... "Are...
Hi all. I made the 6$ gauss meter. Since I had a digital voltmeter, it was only a little bit more then 6 $ (Sweden is NOT a country for R&D). It's great to ...
Eric, I would suggest that you build the "slightly more expensive" version of the meter, but use the last opamp in the quad package as a comparator, fed from ...
Thanks Darren. For now I go for the comparator. Since I'm at this moment (my Bowman project) not really looking for gauss, only for comparing magnets with each...
Hi Darren. I have some problems too find a suitable comparator circuit. Do I understand it right that I need three of them in order to find out if a voltage is...
Hi all. I became member in the egroup of Robert Calloway. At the moment the discussion is about a test that can be done with the attached wheel. In case ...
Hi all. I made a video clip of my Gauss meter prototype. I added a circuit that Darren Kozey (thanks Darren) designed that shows North and South pole with a ...
Hi. I use Microsoft MPEG-4. And Windows Media Player 6.4 (on W2K) Eric. ... From: "Mark Hayton" <mark_hayton@...> To: <minatowheel@yahoogroups.com> ...
Hi Eric nice job on your CKT, which Hall Effect did you use. Its nice to have a visual led and a voltage gauss reading. I did notice a real differance between...
Hi Wayne, I used the A 3515 LUA. It's not calibrated but works fine for me. Since the Hall to not too sensitive I need a distance between magnet and sensor....
Hi Eric, Could you print out the ( Kozey) red-blue light circuit for the gaussmeter and E mail me a diagram? Parts list also. I finally got my hall effect...
Hi all. For those who want to build the Gauss meter with the pole detector I have put the circuit at ...
563
MILEHIGH3D@...
Jan 14, 2004 11:14 pm
Hello Group- Please look at the latest "Nexus" magazine. It shows what may be how to make a magnetic monopole in article about new type of electric motor...
564
MILEHIGH3D@...
Jan 14, 2004 11:16 pm
Check out this site- http://www.flynnresearch.net/rotary_motors.htm -Miles...
565
MILEHIGH3D@...
Jan 14, 2004 11:32 pm
Hi Eric- I saw the ppage with the doughnut/torus. http://www.fdp.nu/mikelldevice/thedevice.asp It does my heart good to see someone take up my suggestion to...
Hello Miles. Yes, I remember. It is message 320 (august 2003) you are referring to. This Torus thinking was (is) very interesting. Regards, Eric. ... From:...
Hi Miles I have tried making a Donut model using 1/4 cubes on a 6" foam donut. Then I wrapped the foam donut with copper tape, get it at hobby stores. Giving...
Hi all. All the talk about the Bowman device made me think. The ratio 1:4.5 (magnets diameter against length) is needed to pull the influence of the other pole...
Eric, when I was looking at your designs I was also thinking the same thing. I has wondering if you can use some type of magnetic shielding rather than longer...
Hi Mark. I never found shielding material that shielded permanent magnets. The material I tried before was the kind that is placed in front of a computer...
Well, it is just to experiment with, I will get it probably next week and I am going to do some testing with it. So, I will let you know the results. Mark...
I also found some 1:8 ratio rod magnets that I ordered. They are a very small diameter, but I thought I could use them to make a very small wheel to experiment...
Hi All, I have a lot of that stuff laying around in my garage. It acts like an iron sheet to permanent magnets. Its real use is in shielding ELECTRO magnetic...
575
MILEHIGH3D@...
Jan 16, 2004 2:21 am
Hi Group- Look at the THANE info I sent. It may have a design for a magnetic monopole gate to prevent the end of the magnet/wheel from reversing- Miles...
Hi Miles. What THANE info? Eric. ... From: MILEHIGH3D@... To: minatowheel@yahoogroups.com Sent: Friday, January 16, 2004 3:21 AM Subject: Re: [minatowheel]...
