Hi, My name is Jameel Shaheed and I have recently purchased the Progo Software for the TJ Pro Robot. I am having a hard time compileing some of the files...
I just bought one of these sonar sensors for our university project. We are using this sensor to dectect a vehicle anywhere from 20 to 5 feet away from another...
I would first use it in your application and see how the current settings work. If you find you need to adjust it turn those pots slowly while watching the...
Scott Jantz
scott@...
Mar 12, 2003 2:57 am
1260
What operating system are you using and what software. Also all the information on ports etc is in the manuals at www.mekatronix.com --Scott ... From:...
Scott Jantz
scott@...
Mar 12, 2003 3:00 am
1261
Not coping to the proper place means you need to setup paths properly. Read the TJ Pro Users Manual. It gives you all the information you need to do that. This...
jack
jack@...
Mar 12, 2003 1:44 pm
1262
Refer to the MUST Users Manual (Download gratis from <ww.mekatronix.com>->Manuals). jack ###...
jack
jack@...
Mar 12, 2003 2:00 pm
1263
What I don't understand is the pots for the zero and the full scale are "12 turn". I am only in the stage of testing the senor out via a voltage meter. It...
The full scale is the gain and the zero is the sensitivity. Again I would not touch either until you know you want to change the range. --Scott ... From: q q...
Scott Jantz
scott@...
Mar 13, 2003 12:25 am
1265
we were probing into two front IR sensors<TJPro> and all of a sudden the robot stopped working and started jerking and all that stuff.we had loaded the...
You probably shorted power and ground. Usually this causes no long term damage but the robot may not immediatly work due to an overheated regulator. I would...
Scott Jantz
scott@...
Mar 17, 2003 1:41 am
1267
Is it me or any FAQs related to most controllers, the 68HC11 included WAY out of date? I seriously thought of taking on the challenge of writing one. The...
It should work it may require a different bootloader but I think the HSSDL11 will do it. You will want to turn off the on chip memory. --Scott ... From:...
Scott Jantz
scott@...
Mar 19, 2003 12:45 am
1271
Michael, Post any proposed FAQ for the group for possible correction or acceptance. Mekatronix will evaluate them, as we hope the rest of the group will, for ...
jack
jack@...
Mar 21, 2003 5:11 pm
1272
Jack, I put it in the Files section if you get a chance. It's been slow going so far. I dug around this group and read a bunch of the problems and answers to...
Download the TALRIK II Assembly Manual and the TALRIK II Users Manual, gratis, from <www.mekatronix.com>. All the issues you mention are discussed at length in...
jack
jack@...
Mar 21, 2003 8:53 pm
1274
Jack, Yes, I did, thanks. I also went to the Motorola site and the 68HC11 Manual had what I would call a generic version of how to run code the first time. I'm...
I uploaded some changes I made this weekend. Mainly on the section regarding bootstrap mode, which needs to be double-checked. I obtained most of it from the...
i have been lurking in the darkness of this group since i joined. i'm trying to get a feel for the good and bad of the HC11 micro. it looks good, but can it...
As a microcontroller it is excellent. If you have a C cross-compiler Refer to < www.mrrobot.com >: Part# ICC11-w5 C-Compiler & Interactive Development...
jack
jack@...
Mar 24, 2003 7:26 pm
1278
I received my MRC11 bare board along with the comm and expansion board. However it looks like the parts list doesn't contain quite the complete details that...
I am using the Must01a/40+ sensor. I am starting to get no readings whatsoever. I adjusted it to max range and then down to min range and my program is still...
In case someone else decides to build the MRC11 board yourself I ran into trouble trying to find the MC34064 & MC34164, LM2931T-5.0., I found them at: ...
make sure the sensor is clicking this means the transducer is working. some times the transducer comes loose from the board. --Scott ... From: Joey...
Scott Jantz
scott@...
Mar 27, 2003 11:42 pm
1282
Yes its clicking, however the rate at which it clicks has slowed slightly. It is almost as if the sensor all of a sudden requires move voltage because when ...
It sounds like your power supply is the problem. --Scott ... From: q q [mailto:qqjjz@...] Sent: Thursday, March 27, 2003 9:59 PM To:...
Scott Jantz
scott@...
Mar 30, 2003 4:27 pm
1284
That was half the problem. The sensor was working fine with an ADC circuit I built. All of a sudden one day it just didnt like it. I found out it was the ...
I recently purchased the MustA01a usonic sensor, but can't get any sort of differing voltage reading from the output pin ( I get a continuous 3.8mV ).... I've...
Hi dears, I am new to this group. If anyone of you have worked on PIC microcontroller, 17c42a in Extended microcontroller mode using peripheral interrupts....
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
