The IR detector has electronic filters with center frequency at 40KHz. If you excite the emitter at 32KHz, which you can do, the IR detector response will not...
jack
jack@...
Nov 1, 2003 11:47 pm
1350
HCload software is a good place to start. You can get a copy from here ... allows you to load an S19 file into the 68HC11 uController. Is the program dump that...
Yep. Try a hall-effect sensor. Sold everywhere¡¦ Run a search on google and volia! Mert ... From: mckenzie_gibson [mailto:mckenzie_gibson@...] Sent: 04...
Are you trying to detect the wire or the current or both, or does it matter? Is the wire in plain view or hidden? At what distance do you want to detect the...
jack
jack@...
Nov 6, 2003 2:10 pm
1354
Hello, i'm working with a TALRIK but the icc11-program(Version 6DEMO) cannnot download the *.s19 "file" to the TALRIK I'm using Win2000, is it possible that...
double check the connections, switch settings, battery voltage. Also do the lights on the MB2325 behave properly when you press reset on the robot. Double...
Scott Jantz
scott@...
Nov 8, 2003 8:05 pm
1356
Hi again, thanks for the answer Scott! The Connectionproblem was because of Windows2000. With Windows98 the Syncronisation(PC-Talrikboard) works, but I cannot...
Did this come fully assembled, partially assembled or unassembled? There is much more to test if it came in kit form. --Scott ... From: "scheinmn"...
Scott Jantz
scott@...
Nov 11, 2003 1:31 am
1358
Sorry,I forgot to tell the errors: the icc11-program says: "Board not responding" the Highspeeddownloader says: "acknowledge mismatch" thanks and greetings max...
Hi! thanks for the answer Scott! the Talrik-Robot was bought from our department in Plymouth, Michigan and then transfered to us here in Germany. The Talrik...
Unfortunately, WIN2000 is the problem. If you can get access to WIN98 or earlier, things should work out fine. Also, contact Image Craft C to see if they have...
jack
jack@...
Nov 14, 2003 8:19 pm
1361
Yes the robot was fully checked out and working before it shipped. Make sure you charge the batteries overnight before using the robot otherwise you may have...
Scott Jantz
scott@...
Nov 17, 2003 3:04 am
1362
Hi! The LEDs on the MB2325 D1 and D2 are working. D1 is lit all the time and D2 when pressing the reset button in downloadmode. I have now another PC, its an...
Hi! the Talrik was charged 40 hours, but I always still have the same appearments as in the last posting. I don't see other possibilities by myself, I need a...
My problem should be simple to solve. I am using the MSCC11 single chip board and am trying to output signals to PORTC. Thus far I have tried the following: ...
The high speed serial download software (HSSDL11) does not come with the Talrik UNLESS you bought a Talrik bundle. (Contact MrRobot to find out what you...
You will need to get your HSSDL11 from salesdept@... Also if you can try another computer we have had some problems with laptops and serial ports. I...
Scott Jantz
scott@...
Nov 23, 2003 11:39 pm
1367
... i doubt i can answer it, but what about the magnetic field? It's just like a amperemeter AC magnetic detected device. Maybe...
I'm an absolute beginner re Robots and Electronics. However, my 7 yr old is interested in building robots. I started by picking up the book Junkbots, BugBots...
Hi! finally my Talrik is alive. The batteries were bad, I had to take some new ones. And the example *.s19 files were bad, with the new compiled ones now...
Yes you will need another battery back for the wireless units. The one with the 6 wire to 20 pin (or something) goes on the robot side and the 6 pin side...
Scott Jantz
scott@...
Dec 4, 2003 3:00 pm
1371
Hi! so the wireless-module which I have to connect with the robot has only its connection with the 12 to 6 pin cable(robot to module)?so it's right that the 4...
Hi everyone. Thanks for the group first off. I'm looking for some advice on a project I'd like to get started on. Here's what I'd like to do: 1.) Control 4...
Hi, I've been looking for another book to read and saw a book, "Programming and Customizing the Hc11 Microcontroller" by Tom Fox. Does anyone have this book?...
Hi again, first of all, happy new year. I didin't try again the wireless connection for some time. Now I tried again, but without success. (hope you remember...
Hi, how does the code get to the memory.. Do I need a Buffalo monitor or does the motherboard(MTJPRO11) have something else for monitoring. Do I only need...
Refer to the tjpro Users Manual on <www.mekatronix.com> ->Manuals . You can download it free. It gives all the details of downloading code into the MTJPRO11...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
