Hi I have a question about IR Detector,Why we should hack IR Detector and convert it from digital to analog? Why we can't use it as digital Detector? thanks ...
The ranging depends on the intensity of the modulated signal received and not on the information carried on the modulated wave. Just detecting the digital...
jack north
jack@...
Aug 8, 2004 7:34 pm
1430
The problem is not the hardware, but the software. Find a hand-held computer that communicates with a hard drive, if there is one, otherwise, your robot needs...
jack north
jack@...
Aug 8, 2004 7:34 pm
1431
The only advantages I see in a parallax stamp is intensive modules that work with the stamp. I perfer to code in C but I would like technical support. Also I...
My first question is, what is the sensor minimal and maximal sensing limit? I the documentation in mrrobot site is given 6inch to 15 feet, but I have reached...
It sounds like the gain pot needs to be adjusted. Move it in small increments and see if the long distance measurement gets better. --Scott ... From: ro_rbt...
Scott Jantz
scott@...
Aug 26, 2004 12:19 am
1434
Where is it in the documentation on which settings are what when using a dip switch on board the MRC11? Michael...
the DIP switch would fufil the same circuit requirements as the external switches. Look at the TALRIK manual on www.mekatronxi.com for more information. ...
Scott Jantz
scott@...
Sep 9, 2004 10:47 pm
1436
Scott, Thanks. I ended up looking in the 68HC11 manual and it showed the modes and logic and then looking at the schematic figured it out. I'll probably put it...
Scott, I even made an Excel spreadsheet showing the DIP switch settings and which mode they are if you want me to upload it? That or have someone to verify it...
I'm writing here to complain about the Mechatronix datasheet and hardware that doesn't fit together regarding the MUST01 sonar sensor. In the Data Sheet it is...
I finally did it. I built my MRC-11 from scratch. I bought the bare board and then bought the parts from several sources. Then came the fun part of getting...
You were probably looking at the wrong datasheet. There are two sensors, one of them has a 5v input and the other has the 8 to 16. The MUST01 was the 5v...
feel free to post anything you want related to your project including the excel sheet. Although it might be easier to do in text in a message and people will...
Scott Jantz
scott@...
Sep 14, 2004 2:01 pm
1442
Scott, Thanks. I added the DIP switch one. Is it okay if I go ahead and add say the assembly test files that Mekatronix has such as memory test ones as they...
Thats fine just reference the page. --Scott ... From: Michael Monteith [mailto:michael_r_monteith@...] Sent: Tuesday, September 14, 2004 4:27 PM To:...
Scott Jantz
scott@...
Sep 17, 2004 2:31 pm
1444
I added some files that helped me. One which is HCload. Although it's not developed any further it was quick and easy to download programs to my MRC-11 and...
What C compiler is anyone using with the 68HC11? I've been toying with GNU's GCC for 68HC11 at: http://m68hc11.serveftp.org/m68hc11_gcc.php Looks nice but not...
I am in need of gripper robot arm that has an XYZ staging. This arm would be used to grab and pull a jewel cased CD from a shelf. We basically have some 5...
New Statistical Analysis CODE for new Statistical Analysis Statistical Analysis is wrong if you flit a cone you have a 50 50 chance but if a robot flips a cone...
I am currently using the ICC11 Version 5 compiler. However, the libraries provided only include a "subset" of C. I am looking for a compiler or additional...
To whom it may concern; I'm interested for the Talrik 2 project kit but I have few doubts need to clear by you.If I purchase the Partially Assembled Talrik II ...
Does anyone know of a female connector I can use on the MRC-11 that I can plug into the board with solderable ends? Most of the ones I've seen are for ribbon...
The TALRIK II robot provides the basic robotic platform for you to program...limited only by your imagination, time and money. The basic routines supplied...
jack north
jack@...
Oct 27, 2004 11:31 am
1452
Okay, I'll give as much details as I can. I'm using a MRC-11 with 64K Ram and a MB2325 board. Using Interactive ICC11 version 5. In Bootloader Options I...
I would connect 3 IDC connectors 2 normally to the 2 boards and the 3rd on a longer piece of the ribbon cable then place a 2X30 male header in the 3rd IDC and...
Scott Jantz
scott@...
Oct 28, 2004 12:14 am
1454
Scott, I see what you are saying. Right now I'm not using the expansion board, just the MRC-11 alone. But this would even work for this setup too and the I...
Thank you. For replying my mail so soon.How could i program the robot to perform identification, navigation, exploration?Is the programming is already exist or...
Dafydd, Although I'm just really a user here I want to thank you for posting the files you did. When we all start sharing what we are working on, our pains,...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
