can anyone kindly give me a help as to which program/software i will use for my robot. i have existing prog11 and high speed downloader. is there anything else...
What robot do you have? jack ... From: "jt_tejada" <jt_tejada@...> To: <mrrobot@yahoogroups.com> Sent: Thursday, November 10, 2005 5:48 AM Subject:...
jack north
jack@...
Nov 15, 2005 9:54 pm
1544
jack, Actually i have 5 pieces of TJ PRO robot. We offered these as a project for the school and they are asking me to demonstrate or to make a program...
First, go to www.mekatronix.com ->Manuals and download the TJ Pro robot Assembly Manual and the Users Manual. That will get you started. You can also buy...
jack north
jack@...
Nov 21, 2005 12:59 am
1546
Hi, I have a TJPro and I use XP for downloading. You must change the compatibility in properties. Check the check box of Run this program in compatible with...
Hi all, I have a tjpro and I am working in my graduation project. I use the ICC11 compiler. I have some difficulty in compiling. The robot with the software is...
You will need ICC-11 compiler (www.mrrobot.com) or the equivalent freeware version. The former is supported and might be easier for you to get started. jack ...
jack north
jack@...
Dec 20, 2005 6:02 am
1549
Hi jack, i already have the TJ pro assembly manual and user manual. I am already reading it. They have ask me on how to install PROGO11? there is a filename...
Hi all I have a TJPRO robot. It have a problem in the power. Either the power is on or it is off tjpro always receives a 3.6 voltage power and the red led is...
Your power switch is probably broken and because its on all the time the batteries never charge. replace the power switch and it should work fine after an all...
Scott Jantz
scott@...
Jan 8, 2006 6:45 pm
1552
how do i install Progo11?? I found out that there is no "comprogo.bat".ld appreciate your help regarding my project. thanks a lot....
Hi I have tried anoter siwtch. But the same problem remains. When turning the switch off a 3V pass to the red led and It lights but when turning it ON a 5...
Are you sure you have the correct LED in the corrct place in the circuit? could you have the charge LED and the power LED mixed up? I would double check all...
Scott Jantz
scott@...
Jan 10, 2006 11:18 am
1555
... Hi Lina Actually, I have never see the TJPRO Robot. But maybe I can give u some rechecking ask. What did u mean " either the power is on or it is off"? Is...
I have checked the connections, used a new power switch and checked for any short but it does not work. I am working on my graduation project and we are two...
hi everyone, I have this PROGO11 software. In the manual, there is a filename "comprogo.bat" but in my file the filename is "installprogo" which is MS-DOS...
Hi I have tried anoter siwtch. But the same problem remains. When turning the switch off a 3V pass to the red led and It lights but when turning it ON a 5...
It sounds like the other group may have damaged the controller board. You can either send it to us for repair or purchase a new controller board. For repair...
Scott Jantz
scott@...
Jan 20, 2006 8:13 pm
1561
Does anyone had a POGOv13 software? how do i download it? thanks. joseph....
You need the batch file. Open it to edit to see what it does. Progo.c is also needed. If you purchased PROGO11in your bundle, you should have gotten the manual...
jack north
jack@...
Feb 11, 2006 2:17 am
1564
hello, we bought tjpropa last dec 2005 from your store... we have hacked the servo and followed all instructions in the manual but the servo still doesn't run...
A common problem is a short on the battery lines connected to the servos PA3-PA7 blows the trace from the battery. You should just be able to solder a wire...
Scott Jantz
scott@...
Mar 2, 2006 1:05 pm
1566
I was wondering how do we download our assembly code onto the MC68HC11 processor board for the TJPro the interface is just not working for us....
hello, we tried to put a wire from the battery to PA3-PA7...the motor is running even without the servo_on() command...without the wire, the PA3-PA7 has no...
hi anyone, we have a new problem...the motor is already on when we plug the female connector to PA3 & PA7...typing the commands servo_off() or motorp(0,0)...
make sure you centered the pot inside the servo. --Scott ... From: mrrobot@yahoogroups.com [mailto:mrrobot@yahoogroups.com]On Behalf Of youakome Sent:...
Scott Jantz
scott@...
Mar 10, 2006 12:45 pm
1570
With my TJPRO connected to a PC from Com1 to a MB2325A through the Ribbon Cable, I cannot get the pcode download to start. -The Power Switch is ON, and the...
Do you get blinking lights during the download? Do you get an error from IC? --Scott ... From: mrrobot@yahoogroups.com [mailto:mrrobot@yahoogroups.com]On...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
