mrrobot : Messages : 1548-1577 of 1610

Messages: Simplify \| Expand (Group by Topic)		Author	Sort by Date

1548	You will need ICC-11 compiler (www.mrrobot.com) or the equivalent freeware version. The former is supported and might be easier for you to get started. jack ...	jack north jack@...	Dec 20, 2005 6:02 am
1549	Hi jack, i already have the TJ pro assembly manual and user manual. I am already reading it. They have ask me on how to install PROGO11? there is a filename...	jt_tejada	Dec 29, 2005 11:41 am
1550	Hi all I have a TJPRO robot. It have a problem in the power. Either the power is on or it is off tjpro always receives a 3.6 voltage power and the red led is...	lul_hs	Jan 8, 2006 2:27 pm
1551	Your power switch is probably broken and because its on all the time the batteries never charge. replace the power switch and it should work fine after an all...	Scott Jantz scott@...	Jan 8, 2006 6:45 pm
1552	how do i install Progo11?? I found out that there is no "comprogo.bat".ld appreciate your help regarding my project. thanks a lot....	jt_tejada	Jan 9, 2006 11:12 am
1553	Hi I have tried anoter siwtch. But the same problem remains. When turning the switch off a 3V pass to the red led and It lights but when turning it ON a 5...	lul_hs	Jan 9, 2006 9:49 pm
1554	Are you sure you have the correct LED in the corrct place in the circuit? could you have the charge LED and the power LED mixed up? I would double check all...	Scott Jantz scott@...	Jan 10, 2006 11:18 am
1555	... Hi Lina Actually, I have never see the TJPRO Robot. But maybe I can give u some rechecking ask. What did u mean " either the power is on or it is off"? Is...	be ck benn_777	Jan 11, 2006 3:44 pm
1556	actually there may be any short between the phase supply and the led voltage ok kindly plz check it and say me wats the fault ok dnt forget lul_hs...	hari prasad sayhaihari	Jan 11, 2006 3:48 pm
1557	I have checked the connections, used a new power switch and checked for any short but it does not work. I am working on my graduation project and we are two...	lul_hs	Jan 13, 2006 12:22 am
1558	hi everyone, I have this PROGO11 software. In the manual, there is a filename "comprogo.bat" but in my file the filename is "installprogo" which is MS-DOS...	jt_tejada	Jan 17, 2006 3:21 pm
1559	Hi I have tried anoter siwtch. But the same problem remains. When turning the switch off a 3V pass to the red led and It lights but when turning it ON a 5...	lina lul_hs	Jan 20, 2006 8:10 pm
1560	It sounds like the other group may have damaged the controller board. You can either send it to us for repair or purchase a new controller board. For repair...	Scott Jantz scott@...	Jan 20, 2006 8:13 pm
1561	Does anyone had a POGOv13 software? how do i download it? thanks. joseph....	jt_tejada	Jan 22, 2006 12:56 pm
1562	can anybody know where to download POGOv13? thanks...	jt_tejada	Jan 25, 2006 12:28 pm
1563	You need the batch file. Open it to edit to see what it does. Progo.c is also needed. If you purchased PROGO11in your bundle, you should have gotten the manual...	jack north jack@...	Feb 11, 2006 2:17 am
1564	hello, we bought tjpropa last dec 2005 from your store... we have hacked the servo and followed all instructions in the manual but the servo still doesn't run...	youakome	Mar 1, 2006 1:07 pm
1565	A common problem is a short on the battery lines connected to the servos PA3-PA7 blows the trace from the battery. You should just be able to solder a wire...	Scott Jantz scott@...	Mar 2, 2006 1:05 pm
1566	I was wondering how do we download our assembly code onto the MC68HC11 processor board for the TJPro the interface is just not working for us....	lamariousc	Mar 4, 2006 12:40 am
1567	hello, we tried to put a wire from the battery to PA3-PA7...the motor is running even without the servo_on() command...without the wire, the PA3-PA7 has no...	youakome	Mar 8, 2006 2:22 pm
1568	hi anyone, we have a new problem...the motor is already on when we plug the female connector to PA3 & PA7...typing the commands servo_off() or motorp(0,0)...	youakome	Mar 9, 2006 8:23 pm
1569	make sure you centered the pot inside the servo. --Scott ... From: mrrobot@yahoogroups.com [mailto:mrrobot@yahoogroups.com]On Behalf Of youakome Sent:...	Scott Jantz scott@...	Mar 10, 2006 12:45 pm
1570	With my TJPRO connected to a PC from Com1 to a MB2325A through the Ribbon Cable, I cannot get the pcode download to start. -The Power Switch is ON, and the...	wrightski1	Mar 10, 2006 12:49 pm
1571	Do you get blinking lights during the download? Do you get an error from IC? --Scott ... From: mrrobot@yahoogroups.com [mailto:mrrobot@yahoogroups.com]On...	Scott Jantz scott@...	Mar 12, 2006 12:28 am
1572	what do you mean? what is the pot? we hacked the servo by removing the board attached to it and burning the inside of the bottom part, of the largest gear so...	youakome	Mar 13, 2006 2:19 pm
1573	Are you sure you did the right servo hack? You have to leave the electronics inside if you are using it with the TJ Pro robot....	robots2000us	Mar 13, 2006 3:15 pm
1574	YES we are using tjpro...we followed the manual...it said unsolder the motor from the board and we did...we left only the gears and potentiometer...	youakome	Mar 13, 2006 3:54 pm
1575	we were able to make tjpro run...the motors were completely working...but we wanted to change the motors rotation to the other side so we INTERCHANGED the red...	youakome	Mar 15, 2006 3:11 pm
1576	YES we are using tjpro...we followed the manual...it said unsolder the motor from the board and we did...we left only the gears and potentiometer...	minette are youakome	Mar 15, 2006 3:12 pm
1577	That is incorrect you need the board back. The manual does not say to remove the board. --Scott ... From: mrrobot@yahoogroups.com...	Scott Jantz scott@...	Mar 15, 2006 3:13 pm

Yahoo! Groups Tips

Did you know...

Messages

Yahoo! My Yahoo! Mail
	Sign In New User? Sign Up
		Tech - Groups - Help

Yahoo! Groups Tips

Did you know...

Best of Y! Groups

Messages