hello, we bought tjpropa last dec 2005 from your store... we have hacked the servo and followed all instructions in the manual but the servo still doesn't run...
A common problem is a short on the battery lines connected to the servos PA3-PA7 blows the trace from the battery. You should just be able to solder a wire...
Scott Jantz
scott@...
Mar 2, 2006 1:05 pm
1566
I was wondering how do we download our assembly code onto the MC68HC11 processor board for the TJPro the interface is just not working for us....
hello, we tried to put a wire from the battery to PA3-PA7...the motor is running even without the servo_on() command...without the wire, the PA3-PA7 has no...
hi anyone, we have a new problem...the motor is already on when we plug the female connector to PA3 & PA7...typing the commands servo_off() or motorp(0,0)...
make sure you centered the pot inside the servo. --Scott ... From: mrrobot@yahoogroups.com [mailto:mrrobot@yahoogroups.com]On Behalf Of youakome Sent:...
Scott Jantz
scott@...
Mar 10, 2006 12:45 pm
1570
With my TJPRO connected to a PC from Com1 to a MB2325A through the Ribbon Cable, I cannot get the pcode download to start. -The Power Switch is ON, and the...
Do you get blinking lights during the download? Do you get an error from IC? --Scott ... From: mrrobot@yahoogroups.com [mailto:mrrobot@yahoogroups.com]On...
Scott Jantz
scott@...
Mar 12, 2006 12:28 am
1572
what do you mean? what is the pot? we hacked the servo by removing the board attached to it and burning the inside of the bottom part, of the largest gear so...
we were able to make tjpro run...the motors were completely working...but we wanted to change the motors rotation to the other side so we INTERCHANGED the red...
That is incorrect you need the board back. The manual does not say to remove the board. --Scott ... From: mrrobot@yahoogroups.com...
Scott Jantz
scott@...
Mar 15, 2006 3:13 pm
1578
order 2 more servos from www.mrrobot.com you can get them already hacked so you can just plug them in. --Scott ... From: mrrobot@yahoogroups.com...
Scott Jantz
scott@...
Mar 16, 2006 12:52 pm
1579
Hi, I am buying the MTJPRO11 microcontroller board and I was looking for software for Mac OS X: Both an assembler/compiler and a program for downloading...
D2 blinks ON and OFF whether or not I "OK" the download from ICWIN. In other words, I don't see a difference in the blinking from before I "OK" the download to...
Somehow you are not connecting to the right serial port. When you download the P-code the lights should blink rapidly. Check to make sure you are connected...
Scott Jantz
scott@...
Mar 25, 2006 3:42 pm
1582
Thanks Scott, I've already tried all the combinations that I can think of. I am getting nowhere. I have made sure that there is no other driver set to the Com1...
we hav hacked the IR detectors (those inside the tin cans)& followed all the instructions... when both the Detectors & emitters (leads) are plugged to the...
It sounds like the detectors are fine (85 is the no-IR level) your LEDs are either not on, in backwards, or not modulated at 40kHz. --Scott ... From:...
Scott Jantz
scott@...
Apr 21, 2006 12:00 pm
1585
hi scott, how do we put on the LEDs? How will we modulate it at 40 kHz or is it modulated already? we didnt change anything in the robot...we only followed all...
Hi everyone, I'm trying to use IC 3.1 for Mac. When I first start the program, I get an error dialog box: "Screwup Reading a Character." If I click "ok" it...
Send me your address and I post you a couple CNY70 (10mm range IR sensors)sensors for free. youakome <youakome@...> wrote: we hav hacked the IR detectors...
is it like that? is should not return 84 or 85 yaar theres some thing wrong in it y dont u check it again/ baskan kalezade <bkalezade@...> wrote: Send me...
Thanks god I found this place. I got a TJ-pro kit and have few questions for all you highness. 1) I hookup all the wires and can successfully download the...
Hi everyone, I am looking into building a robot that climbs poles/lamposts for visual inspection. Any advice/ ideas /comments would be gratefully appreciated. ...
... Possibly. Do you think you didn't solder it well? ... See the schematic on page 21 of the TJ Pro Assemby Manual. Port C is brought out to the 8 pins...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
