... are you seeing the LEDs on the MB2325 board flash? Both of them? Also what Com port are you using and is it a USB based com port or are there any ...
Scott Jantz
scott@...
Dec 3, 2008 7:29 pm
1608
Ok so I checked my version of IC and I believe I have the commercial version (v3.2) as opposed to the freeware version (which is v2.8, correct?). I was...
It's probably because you are using the freeware version which is not supported by the manufacture (or anyone). You can purchase the latest version of IC...
Hi, I just bought a TJ-Pro and I am having problems loading the initial code onto the robot. Upon installing the Interactive C freeware and attempting to...
Saleem, I found it at: http://www.mekatronix.com/detailed/mrc11.htm I still have it, the MRSX-01 and the MB2325 board. I'd like to get rid of it since I have...
I couldn't find it either except on their FAQ: http://www.mrrobot.com/faqsmeka.html It's probably in their documentation sections too. Not sure what the deal...
I built my MRC-11 and communication board but now going a different direction. If you'd like it contact me personally off of here. I'd hate to see it go to...
Does anyone have any idea what the precision is for the analog input on the TJ Pro or where I might find that information? When you query analog(2); for...
Hi Jess, I believe you will need to purchase the MB2325 or the USB2325 separately in order to connect the TJ Pro to your computer for programming. If you plan...
2 things, make sure you charge your battery and check the mode switch wiring. ... From: mrrobot@yahoogroups.com [mailto:mrrobot@yahoogroups.com]On Behalf Of...
Scott Jantz
scott@...
Nov 26, 2006 10:27 pm
1596
When the robot is connected to the MB2325 and turned on, the D2 light comes on, but when I hit the reset button, it simply stays on. It will not go off, and I...
I haven't done this myself, but it should be possible as the CMUcam only needs a serial port to communicate with the main board. According to the specs of the...
... Possibly. Do you think you didn't solder it well? ... See the schematic on page 21 of the TJ Pro Assemby Manual. Port C is brought out to the 8 pins...
Hi everyone, I am looking into building a robot that climbs poles/lamposts for visual inspection. Any advice/ ideas /comments would be gratefully appreciated. ...
Thanks god I found this place. I got a TJ-pro kit and have few questions for all you highness. 1) I hookup all the wires and can successfully download the...
is it like that? is should not return 84 or 85 yaar theres some thing wrong in it y dont u check it again/ baskan kalezade <bkalezade@...> wrote: Send me...
Send me your address and I post you a couple CNY70 (10mm range IR sensors)sensors for free. youakome <youakome@...> wrote: we hav hacked the IR detectors...
Hi everyone, I'm trying to use IC 3.1 for Mac. When I first start the program, I get an error dialog box: "Screwup Reading a Character." If I click "ok" it...
hi scott, how do we put on the LEDs? How will we modulate it at 40 kHz or is it modulated already? we didnt change anything in the robot...we only followed all...
It sounds like the detectors are fine (85 is the no-IR level) your LEDs are either not on, in backwards, or not modulated at 40kHz. --Scott ... From:...
Scott Jantz
scott@...
Apr 21, 2006 12:00 pm
1583
we hav hacked the IR detectors (those inside the tin cans)& followed all the instructions... when both the Detectors & emitters (leads) are plugged to the...
Thanks Scott, I've already tried all the combinations that I can think of. I am getting nowhere. I have made sure that there is no other driver set to the Com1...
Somehow you are not connecting to the right serial port. When you download the P-code the lights should blink rapidly. Check to make sure you are connected...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
