I am trying to decide whether to use a PIC STAMP or HC11 microcontroller for my robot project. Any help questions/or comments on either.. Thanks JOE...
40
Krauland, Mary
kraulanm@...
Dec 2, 1999 7:22 pm
Hi, I have a question about the Mindstamp Prototyping System. There is no mention of ROM, monitor, or debugger. Does this system contain these? Thanks ...
41
frank h falk
ffalk@...
Dec 3, 1999 11:42 pm
Just received my order, 14149. According to the web page I was to get a PDF manual with the MUST01A ultrasonic sensors. Can you tell me where I can get it?...
42
Novasoft11@...
Dec 4, 1999 12:38 am
... I'll send it to you....
43
Boring, Joseph
BoringJ@...
Dec 6, 1999 7:33 pm
I am trying to make a device that will count people passing in a hallway and then relay the total to a base station. Not only do I need to know the count but ...
44
Scott Jantz
scott@...
Dec 6, 1999 9:11 pm
What you describe sounds fine, if you need another serial port you can add an MSCC11 with an E2 68hc11 programmed to send data out its serial port under ...
45
Daniel buergin
daniel.buergin@...
Dec 9, 1999 5:19 pm
Dear Mr. Robot
I have a little Problem (or Question):
When i recompile the libbug.a from the buged01.zip
Distribution, i get these Warnings from swingctl.c...
46
jack
jack@...
Dec 9, 1999 10:56 pm
The actual values for the table are generated by the #defines in calibug.h in the include directory. These values exceed the maximum value of a positive...
47
jack
jack@...
Dec 9, 1999 10:58 pm
The actual values for the table are generated by the #defines in calibug.h in the include directory. These values exceed the maximum value of a positive...
48
jack
jack@...
Dec 9, 1999 11:24 pm
When you purchase MindStamp you get a User's Manual that explains how to use the software packages mentioned below. The table of contents of that manual is at...
49
jack
jack@...
Dec 9, 1999 11:37 pm
Joe, The answer...ready for this...it DEPENDS! PIC is quick to get started and a little easier to use, but is limited in expansion and programming...
50
dasanayakav@...
Dec 16, 1999 4:09 pm
I am working on a project that needs controling 12 R/C Aircraft type servos, two propulsion motors with some kind of encoding to figure distance traveled, 4-6...
51
Scott Jantz
scott@...
Dec 17, 1999 6:30 pm
Your best bet is to combine two boards from Mekatronix (www.mekatronix.com). The MSCC11 with the servo16 program will control your servos and the...
52
Novasoft11@...
Dec 20, 1999 10:22 pm
Thank you for your interest! Due to print lead times, the only catalog we have available is the electronic one that is on the web at http://www.mrrobot.com/ We...
53
Narek Manouk
narek@...
Dec 21, 1999 7:17 pm
Hello, I am looking for a software similar to the High Speed Downloader (HSSDL11) for the 6811, except that I need it to be able to program an external EEPROM....
54
Novasoft11@...
Dec 21, 1999 9:35 pm
... (HSSDL11) ... Try some of the freeware at: http://www.mrrobot.com/downloads.html I think there are a few windows based downloaders there....
55
Scott Jantz
scott@...
Dec 22, 1999 2:15 pm
Yes ICC11 is your solution but if you are not intrested in switching compilers PCBUG11 should still work try it and find out. --Scott...
56
Paul Sample
kadabra@...
Dec 23, 1999 6:35 pm
Ok, what file do I send my TJ Pro when I first start up IC? It has the following Handy Board 1.2.icd, MIT 6.270 2.21.icd, Rug warrior 1.1 or Rug warrior Pro? I...
57
Scott Jantz
scott@...
Dec 23, 1999 7:27 pm
You should have downloaded a variety of software with your TJPRO contact your distributor to find out where to get the software from. It will include the ...
58
Novasoft11@...
Dec 23, 1999 8:17 pm
... No, put the tjpro.icd in the same directory as the others and use tjpro.icd....
59
Jim Jahncke
jim@...
Dec 27, 1999 10:53 pm
I cannot find the TJ Pro distribution software that I need to progrom my robot. Where can I locate this software?...
60
Novasoft11@...
Dec 27, 1999 11:49 pm
... Contact the distributor you bought it from. If you bought it from Novasoft, e-mail your name and invoice number to: novasoft11@... and say you need the...
61
Dheera Venkatraman
dheera@...
Dec 31, 1999 10:52 pm
The Talrik Junior manual pages refer to a program called avoidtj.s19 . Where can I find this file? Thanks, Dheera Venkatraman dheera@......
62
Novasoft11@...
Jan 5, 2000 1:49 pm
... It comes in with system software....
63
jack
jack@...
Jan 11, 2000 3:06 pm
The program avoidtj.s19 comes with the TJ Distribution Software which is bundled with your TJ robot purchase. Our distributors have various means of...
64
jack
jack@...
Jan 11, 2000 3:08 pm
See above reply. jack ########## novasoft1-@... wrote: original article:http://www.egroups.com/group/mrrobot/?start=62 ... ....
65
erwinadi@...
Jan 12, 2000 9:37 am
I think the circuit schematic for the MB2325 is incorrect (and its PCB, accordingly). In schematic page 10 of ...
66
Glenn Bowering
024214b@...
Jan 13, 2000 7:24 am
I was wondering if anyone knows of any techniques to allow robots to communicate with each other. Or of any hardware that might be out there that I could use...
67
Daniel Buergin
daniel.buergin@...
Jan 13, 2000 10:47 am
Hi Is there any Information about programming a ROBOBUG in pure 68HC11 Assembler ? My ROBOBUG works fine under ICC11, but i would like to learn how to progam...
68
MrRobot Customer
mrrobotcustomer@...
Jan 14, 2000 11:58 pm
... toward the 6 ... communication so this ... to a ... other boards ... Just make ... before...
