This must be a compiler set up problem go though the procedure in the TJPRO user manual (at www.mekatronix.com) carefully and try it again. Some files or...
Scott Jantz
scott@...
Jan 1, 2001 11:32 pm
462
Hello, Do you have a product of microcontroller system based on MC68HC11 version F1? That's all. Hope to hear from you soon. Thank you. Ridzuan. Universiti...
mdridzuan767@...
Jan 2, 2001 4:04 am
463
Scott, I recently bought a TJPro and am using the Linux version of the ICC11 5.0 compiler. I observed the same problem about the "undefined symbol __asrd" and...
vagabond@...
Jan 2, 2001 5:10 pm
464
__________________________________________________ Do You Yahoo!? Yahoo! Photos - Share your holiday photos online! http://photos.yahoo.com/...
Josh Belzman
jbelzman@...
Jan 2, 2001 5:30 pm
465
Hello! I am going to build a robot,which is going to be controlled over the internet. The robot is going to be connected to a Pc or a laptop. Also, a web...
Dirzo Loyra
temanascludo@...
Jan 2, 2001 11:25 pm
466
No we have seen no need for the F1 since it would only save 2 chips on the board and the F1s are generaly more expensive. --Scott ... Shop Safely Online...
Scott Jantz
scott@...
Jan 2, 2001 11:51 pm
467
That sounds right thanks for the suggestion. --Scott ... Shop Safely Online Without a Credit Card http://www.rocketcash.com...
Scott Jantz
scott@...
Jan 2, 2001 11:55 pm
468
Yes, not only will the TJPRO work but we have a RF RS-232 kit and wireless camera that would enable the robot to do all that you want. For prototyping you...
Scott Jantz
scott@...
Jan 2, 2001 11:56 pm
469
I wish to hook up some 5volt reed realys to port 'B' on the HC811 (as these are output only). But I need to know that type of output gate this port has - token...
pjc@...
Jan 3, 2001 8:51 am
470
The TJ Pro would be ideal for this project. To get full functionality for your web operators, you should get the following add-ons: 1. RF Data link, Mekatronix...
jack
jack@...
Jan 3, 2001 4:23 pm
471
Paul, The electrical specifications for the MC68HC11 Port B pins can be found in Motorola's 68HC11 Users manual. You can download this gratis from the ...
jack
jack@...
Jan 3, 2001 4:28 pm
472
No, but you may want to consider our variety of 68HC11 microcontroller systems: MTJPRO11 MRC11 MSCC11 Regards, jack ##############...
jack
jack@...
Jan 3, 2001 5:00 pm
473
The ports will drive a reed relay with no problem (250ohm of coil resistance) much beyond that I would use a high current buffer/relay driver or NPN...
Scott Jantz
scott@...
Jan 4, 2001 2:59 am
474
Thanks - that gives me about 20mA. I have looked once again though the documentation from verious places and have not found any clear data that tells me what...
pjc@...
Jan 4, 2001 10:24 am
475
I think I found the information that you are looking for. On page 50 of the "M68HC11 Reference Manual" that is in PDF format on the Mekatronix web site: ...
vagabond@...
Jan 4, 2001 1:55 pm
476
Thanks very much for this - I'll let you know how I get on! :0) Paul...
pjc@...
Jan 4, 2001 11:39 pm
477
I am interested in using the 68hc11e2 mcu sold by mrrobot. Do I need any special hardware to write to the eeprom of this chip. Thanks, Scott...
medgearhead@...
Jan 5, 2001 1:15 am
478
How can I write a process in IC11 V5 for Win that will operate at the same time with anther procedure? In C there is a possibility to begin process or to kill...
Eyal Hershko
air_shko@...
Jan 5, 2001 2:14 pm
479
No it is all contained on the chip and MSCC11 assuming you have the MB2325 and C2325 to interface it to a PC. I also recomend ICC11 for programming although...
Scott Jantz
scott@...
Jan 6, 2001 12:10 am
480
If you want a more full featured operating system you might want to try IC it works well on the TJPROs but will not work on MSCC11s or TJs. In ICC11 there was...
Scott Jantz
scott@...
Jan 6, 2001 12:13 am
481
Hi Scott Two questions 1 - I am working with Talrik II boards, do IC works with it? 2 - Where I can get IC programmer? and how can I down load it to the Robot?...
hershko eyal
air_shko@...
Jan 6, 2001 5:22 am
482
Another option for doing multi-tasking that uses the ICC11 Compiler is the uC/OS-II Operating System. (http://www.Micrium.com) The operating system is...
vagabond@...
Jan 8, 2001 4:50 pm
483
Scott, Mekatronix has good news for you! MR ROBOT will be announcing the product described below in the near future, as it has wide implications for all...
jack
jack@...
Jan 11, 2001 3:09 pm
484
Eyal, Only parts of IC will work on the TALRIK II as is. Using peek() and poke() and some assembly coding permitted by IC, you might be able to use IC to take...
jack
jack@...
Jan 11, 2001 4:05 pm
485
My computer only has USB. No old fashioned serial. What kind of adapter do I need for the serial cable for TJ? Thanks...
mrudney@...
Jan 12, 2001 7:40 am
486
I've had a few questions about why one gets an e-mail everytime someone posts a message in this group. Unfortunately egroups defaults to that setting. You can...
novasoft11@...
Jan 12, 2001 3:03 pm
487
... I've heard of people using a USB to serial converter, but I'm not sure how well that works. Also, I've heard of some of the Mac users taking out their ...
novasoft11@...
Jan 12, 2001 3:04 pm
488
My husband found the Kevin Ross MC68HC....page and there are so many things to choose from. Can anyone give me a push in the right direction as to what we...
banana@...
Jan 13, 2001 8:08 pm
489
Does anyone know where I can find detailed instructions for writing 68HC811 Assembler code (ie. BRSET ?????) I have a list of OPcodes but not how they are...
pjc@...
Jan 19, 2001 1:19 am
490
I have read that the undefined_asrd problem has occured before There was a mentioning of rebuilding the library files Is this necessary and if so how do i do...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
