There is a new update to the highspeed downloader. It takes care of the "feature" that moved servos in some robots as programs were being downloaded. The new...
novasoft11@...
Jun 3, 2001 2:23 pm
725
Hi, I put together my Talrik Jr. Pro robot this weekend and everything went nice and smoothly. Yay. However, now I get to work with Interactive C v3.2. I...
dodd@...
Jun 7, 2001 2:19 pm
726
Dod, You have several issues. I address below. jack ######## ... Check your servo hack. Be sure to remove the potentiometer clip inside the underneath side of...
jack
jack@...
Jun 7, 2001 2:47 pm
727
Thanks for your help Jack, Servos are fine, both move with the default software loaded. ... inside the ... motion. Read the sequence from the .txt files and...
dodd@...
Jun 7, 2001 6:08 pm
728
Answering my own questions in case they may benefit someone else... The baud rate problem was solved by removing the MB2325 board from the PC and/or rebooting...
dodd@...
Jun 7, 2001 9:43 pm
729
Has anyone attempted to connect a small IDE disk drive to the MC68HC11 controller? Can this be done? What other options would there be for larger non-volatile...
lunzewj@...
Jun 7, 2001 9:57 pm
730
Brice, I just built a TJPro and received the IC3.2 software with it. I also see the same version on my board. After synchronization I see the message Pcode...
dodd@...
Jun 7, 2001 10:05 pm
731
DOWNLOAD is used to download ".s19" files from the PC into the robot. Once the program has been downloaded into the robot, you must switch to RUN mode and...
jack
jack@...
Jun 8, 2001 9:26 am
732
Dodd, See comments interspersed in your comments and questions. jack P.S. When I execute IC I get Welcome to Interactive C v3.2 Copyright (C) 1997 Newton...
jack
jack@...
Jun 8, 2001 11:12 am
733
Actually there is. There is a company called MVS that makes a product that they call a stamp drive. It is a RS-232 interfaced board that uses ether compact...
cbuffon@...
Jun 8, 2001 1:26 pm
734
Hello I am looking for a motion control developers kit, preferably low cost as I am doing this for a school project. Ideally it would include a controller,...
pstrittmatter@...
Jun 8, 2001 4:08 pm
735
Pat, I. A MindStamp with the MSCC11 would be a low cost way of controlling up to 16 MS492 servos. These servos already have the amplifier and set point ...
jack
jack@...
Jun 8, 2001 5:16 pm
736
Jack Thanks for all of the great info. I'm sure one of those solution will work for me. With respect to the MindStamp products, you mention the free software...
pstrittmatter@...
Jun 8, 2001 7:05 pm
737
I loaded avoidtjp.c into the robot and the bumpers work fine. However, I don't seem to be getting any voltage across the IR Header pins. I tried using...
dodd@...
Jun 9, 2001 5:23 am
738
Pat, By the way, you can download the circuit diargrams and layouts of all our board and robots gratis. Just go to <www.mekatronix.com> and select MANUALS in...
jack
jack@...
Jun 9, 2001 8:26 am
739
Dodd, Be sure BOTH IR LEDs are connected correctly. The yellow wire of the plug should attach to the longer of the two pins on both, provided you have the ...
jack
jack@...
Jun 9, 2001 8:54 am
740
... WHOOPS!! PLEASE NOTE: The most current version is 2.06 build 23...
novasoft11@...
Jun 11, 2001 6:04 pm
741
Jack, I didn't get the Power Users kit. Therefore I guess I didn't get sensetjp.c. I am a C programmer and didn't really want to learn PROGO since I already...
dodd@...
Jun 11, 2001 6:41 pm
742
hi, i am a senior at uofm in michigan, we have worked with boards purchased from www.axman.com these boards have a Motorolla processor that has A/D conversion...
david vrtachnik
uofmpcdave@...
Jun 12, 2001 2:30 pm
743
hi, i purchased completely assembled TJ-PROs and i wish to add shaft encoders for the same. With totally assembled TJ-PROs is there any way i can remove the...
Atul Suri
asur79@...
Jun 12, 2001 4:04 pm
744
I'm looking for compiler and/or assembler for 68hc11 series microcontroller, that can be developed on a Palmtop.Though i'm able to find some compilers for...
Buddy Ilu
buddy_ilu@...
Jun 12, 2001 4:12 pm
745
The servo horns are glued to the wheels, but you can remove the wheels with a small phillips head screwdriver that fits in the center hole of the wheel. Just...
jack
jack@...
Jun 12, 2001 4:57 pm
746
... If you remove the center screw (though the axel hole of the wheel) the wheel and horn will come off....
novasoft11@...
Jun 12, 2001 5:00 pm
747
Also something I have overlooked is being able to incorporate a simple numeric display via LCD or otherwise as well as have a way for a user to provide inputs...
pstrittmatter@...
Jun 14, 2001 2:07 pm
748
Hello all, I got a question on IR sensors. I have two pairs of infrared receiver and LED. I am using them for object sensing. I used a 555 timer in astable...
happybeaglet@...
Jun 16, 2001 5:43 am
749
Hello I use a very similar circuit than yours on my robot, and I had the same difficulties. The problem was that the detector (I use a Temic/Telefunken TSOP...
olanvin@...
Jun 16, 2001 6:26 pm
750
Hi, Is it possible that the Input capture ports are damaged. Is it possible to test whether they are working. Also, is there some way to understand whats going...
Atul Suri
asur79@...
Jun 18, 2001 2:09 am
751
The ideal transmitter/receiver pair is the Sharp GP2D12 sold by Mr Robot. <www.mrrobot.com>, <sales@...> jack ########...
jack
jack@...
Jun 18, 2001 9:32 am
752
Which board can I connect GP2D12? Thanks, AS....
Atul Suri
asur79@...
Jun 18, 2001 4:02 pm
753
All the mekatronix boards. Plug-and-play. They connect directly with the 3-pin headers on the analog ports for all our microcontrollers and robots. jack ######...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
