Hi sorry for the long time pass till I answer first I am working with more then 4 GP2D12 sensors. for 4 or less the problem is not appear. second I am not...
EYAL HERSHKO
air_shko@...
Sep 1, 2001 10:12 am
852
So the rule seems to be if you use 2 or more GP2D12s you need to run the power to them off a seperate 5V regulator (2931 or 7805 should be fine the 2931...
Scott Jantz
scott@...
Sep 1, 2001 2:30 pm
853
Hi EXACTLY Eyal ... From: Scott Jantz <scott@...> To: <mrrobot@yahoogroups.com> Sent: Saturday, September 01, 2001 4:29 PM Subject: RE: [mrrobot]...
EYAL HERSHKO
air_shko@...
Sep 2, 2001 5:18 pm
854
I am trying to create the .S19 file from the .ASM file. When I open the AS11 program, the DOS screen pops up and says "finished", and I can't even type in the...
electronwaves@...
Sep 5, 2001 9:11 pm
855
AS11 is an old DOS program and must be run from a dos window not clicked on from windows. --Scott ... From: electronwaves@... Reply-To:...
Scott Jantz
scott@...
Sep 7, 2001 1:36 am
856
Actually, OPEN A DOS WINDOW first. Then in that DOS WINDOW, establish a path to the AS11 program and execute it within the DOS WINDOW. Do not call the DOS...
jack
jack@...
Sep 7, 2001 2:43 am
857
ée Hello, This is my first time with this group. I am honored to be here. I am considering using the MRC11U64K/ MRSX01 combination to drive up to 16 servos. ...
Haggai Goldfarb
haggai@...
Oct 1, 2001 10:18 pm
858
you'll want a C compiler, Imagecraft IC11 is nice, we had positive results with it. Do you have assembly experience cause that would help turning pins on and...
david vrtachnik
uofmpcdave@...
Oct 1, 2001 11:43 pm
859
I have connected the Talrik II to the PC, downloaded programs, tested the robot and it is mainly OK, but only 6 IR sensors (from IRDT1 through IRDT5 on the...
Bojan Jerbic
bvjerbic@...
Oct 2, 2001 1:46 pm
860
thanks for responding David, I will be having 2-8 servos max at stage 1 (Although I said up to 16) So a microcontroller with 8 output pins for servo controls...
haggai@...
Oct 2, 2001 5:31 pm
861
To develp your servo controller, should you go with the MSCC11, I recommend the following system configuration, 1. MindStamp with MSCC11 substituted for...
jack
jack@...
Oct 2, 2001 7:14 pm
862
Remove (carfully and slowly with the power off) the 60pin cable that attaches the MRC11 and MRSX01 together. wipe the contacts with isopropyl alcohol and...
Scott Jantz
scott@...
Oct 2, 2001 11:49 pm
863
Dear Scott I did all but nothing happened until I found that IR sensors started to work, giving expected voltage, when I unplugged the charger. I experimented...
Bojan Jerbic
bvjerbic@...
Oct 4, 2001 10:01 am
864
It sounds like the extra noise or too much voltage while charging is causing the mux to not work. We usually keep the robot off while on charge and use...
Scott Jantz
scott@...
Oct 4, 2001 5:23 pm
865
Sorry if this is a bit of a SPAM, but I felt that I'd give you a chance of gitting one of these second hand. Two wheel robot body with modified servos as...
paul.j.clarke@...
Oct 4, 2001 9:02 pm
866
Help ! I just finished assembling my MSCC11 board and started the positive-to-ground short-circuit testing. Unfortunately, I have a problem :( I've uploaded...
Justin
justin@...
Oct 9, 2001 1:47 am
867
Hi Haggai where are you from? Eyal Israel ... From: <haggai@...> To: <mrrobot@yahoogroups.com> Sent: Tuesday, October 02, 2001 7:31 PM Subject:...
EYAL HERSHKO
air_shko@...
Oct 9, 2001 6:29 pm
868
Hi all. Can anyone tell me how I might be able to tell if the MC34064 supplied with the MSCC11 board is faulty ? Also, by what other name or number might it...
Justin
justin@...
Oct 9, 2001 11:46 pm
869
Our technical expert on this subject is out of town and will be back next week and will answer your question then. jack ###### At 02:53 AM 10/9/01 +0100, you...
jack
jack@...
Oct 10, 2001 10:08 pm
870
Hello Jack. Thanks for letting me know - I was beginning to wonder if anyone could help. I look forward to hearing from your expert :) Regards, Justin. ... ...
Justin
justin@...
Oct 10, 2001 11:44 pm
871
I want to 5DOF educational Robot. But i don`t know what driving system must be used. (Dirct drive or indirect drive)?...
farshid_amiry@...
Oct 11, 2001 11:37 am
872
I want to make a 5DOF articulated ROBOT.But i don`t know what driving system must be used?(Direct Drive or Indirect Drive)?...
farshid_amiry@...
Oct 11, 2001 11:41 am
873
Direct drive is extremely costly, but can be more precise than indirect drive. I recommend indirect drive. jack ###########...
jack
jack@...
Oct 12, 2001 2:57 am
874
I dont think you have a problem your mulitmeter is probably just reading the charging of the 5V capacitor. When you have a power ground short the continunity...
Scott Jantz
scott@...
Oct 14, 2001 1:50 am
875
Great ! Thanks - on to the next test then :-) Justin. ... From: Scott Jantz [mailto:scott@...] Sent: 14 October 2001 02:49 To:...
Justin
justin@...
Oct 14, 2001 6:19 pm
876
Hey, I have a 12V DC source that I want to use for power instead of the ~8V source. What is the MTJPRO11 board doing with the ~8V source? I understand that...
The SMT regualor can't handle 12V to 5V for too long (it will overheat and turn itself off) so knock it down some (anything from 5.2 to 8V should be fine even...
Scott Jantz
scott@...
Oct 16, 2001 7:36 pm
878
I am a proud owner of a TJPro, however I'm been playing with it for only a few weeks and its still not working to its full potential. Mr. Robot emailed me...
Do you have lib_tjp.lis, lib_rw11.c, twoservo.c,twoservo.icb,motorp.c These files should define those symbols and you need them to compile avoidtjp.c Dodd ... ...
See comments below. jack ######## ... The libraries for packages a) and c) are not upwardly compatible with b). You should be able to run a) and c) with the...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
