This message is a test followed by some questions about the subject. This request for answers and information is for a military application that my company is...
I could use a little help, if any is available. I have had the TJ-Pro for several months but have not yet attempted to work with it. When I got it (fully...
Hi first - check if your battery are together at list 7.2V second - if you have a modem attach to your computer it will not work. you must work with a...
The bateries are charged and the unit is plugged into power when I try to download to it. There is no modem attached to Com1, but there is a PDA. The two do...
There may be a conflict if you use a program like hot sync the other com port is always in use. I suggest killing the resident program on COM1 disconnect the...
Scott Jantz
scott@...
Jan 15, 2002 11:39 pm
938
Please email me a detailed listing of all the keystrokes and responses so I can see what is going on. Meanwhile.... Some suggestions, although you may have...
jack
jack@...
Jan 16, 2002 2:23 pm
939
Jack: Thanks for the note. I have Com set as stated below, but have NOT relocated the lib_tjp.lis file. I can't find instructions for relocation of that...
Craig, You may have found the problem. D1 should always be lit, it indicates power coming from your P3 to power the MB2325 board. D2 should be off when the ...
jack
jack@...
Jan 16, 2002 5:08 pm
941
The TJ kits have a long piece of a pin connector that looks like it'd be used for jumpers on a PC motherboard or some other electronics appliance, but the TJ...
I am trying to calculate the carrying capacity of the TJ Pro on a sloped course. Can anyone verify the total weight of body platform, including batteries,...
At <http://www.mekatronix.com/brief/brief.htm>you can find the load carrying capacity on a level tiled surface (about 1Kg). The weight of the platform is given...
jack
jack@...
Jan 22, 2002 9:46 pm
946
They are called male headers, female connectors/headers. On Mr Robot's site, under Miscellaneous Parts, you can find F1x36 Single Row 36-pin female header ...
jack
jack@...
Jan 23, 2002 4:30 am
947
Have a TJ Pro Jr. When glueing the abs body together. If the switch supports don't line up perfectally with the bottom plate can I file it or do I need to get...
If you have the TJ Pro assembly manual it's section 6.2 second paragraph. The glue set before I could move the spacer into place. It's offset a little. I need...
The bumper switch supports have a slot to allow the bumper switch-body to fit snuggly into the top plate of the robot. If the slots do not line up, the switch...
jack
jack@...
Jan 26, 2002 4:38 pm
951
Jack: I have only one MB2325 board and, at the time, only one PC available for testing the board due to the size of the port on the board and the ports on PCs...
Craig, The COM restriction you mentioned should only be the case if the other COM ports are used by other devices connected to your PC. ### jack At 07:51 AM...
jack
jack@...
Jan 29, 2002 1:24 am
953
I am evaluating a TJPro for use in teaching a college course on 68HC11 Assembly programming. Can anyone point me to Assembly language resources available for...
Ryan, Answer the following so I can give you a better answer: 1. Do you program in the C language? 2. How many servos do you want to control? 3. Do you want to...
jack
jack@...
Feb 11, 2002 8:36 pm
956
I would like an umbilical cord but RF would be nice. I want to run about 14-16 servos, but only need to run about four or so at the same time, but i need to...
I am having problems using the IC software . The message "board was not found" keeps coming up. I got it to work for a while, and then the error comes up...
I just got through a problem very similar to this one. Are the lights on the board lighting up correctly? I could not connect to the board on the COM2 port on...
For some reason, NT 4.0 will not work with IC software. You might contact <www.newtonlabs.com> to see what they say about it. WIN98, on the other hand, should...
jack
jack@...
Feb 12, 2002 9:44 pm
960
Has anybody used this with the TJ Pro, I am thinking of trying it. What do you think....
For some reason the MJPRO11 board is sending a continuous reset pulse inhibiting communication to and from the mother board. We have checked the voltage...
If you have added extra hardware to the MTJPRO11 that uses the 5V supply you might be over taxing the power supply. You can try adding more capacitance on the...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
