Hello, I just received my LaunchPad board and of course I joined this group. I'm a veteran software engineer with some hardware experience (physical circuit...
Hi everyone, I need help interfacing the eeprom to MSP430F5529 through I2C please. I have looked at the sample codes offered by TI but they are done...
I am using I2C to interface to the lcd controller. We are using the MSP430F5438A chip and the full IAR workbench. I have a scope on the data and clk lines....
mrfiSpiWriteReg(PATABLE,0x7F);// -6 dBm Tx power what does this line means? -6dBm Tx power ?? mrfiSpiWriteReg(CHANNR,0xFB); and whats the frequency selected to...
I am seeing the linker place code for one module in a location that another module has reserved with the DS directive. Details: - IAR KickStart for MSP430...
hi every body i need to know that this statement is setting my frequency or clock of microcontroller whats the frequency its setting BCSCTL3 |= LFXT1S_2; means...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the msp430 group. File : /MC430/Mc430.zip...
Hi Folks, I am migrating a project from the MSP430F5438 chip to the MSP430F5438A chip because the non-A chip is "not recommended for new projects". For the...
I'm going to find out soon enough (it's not crucial that I know before doing the design and writing the critical part of the software), but I'm curious if...
Hey Guys, Thanks to all who tried to help me as I have struggled with this problem. I have placed a file in the files section detailing the algorithm. This...
I've posted here a couple of times about my problems using IAR Kickstart with the LaunchPad and other devices, when running on my Win7 Ultimate 64-bit machine....
I'm curious about taking a look at code for existing, good quality PI or PID control loop control over the DCO vs an external 32kHz crystal. Not calibration...
Hi all, I was just wondering if I have a unit running on a battery how I can swap the supply voltage with the VBUS when the MSP430F5529 is connected to PC...
Hi all, I have a MSP-Experiment board and a PAN1323 development board attached. I am trying to find a software to run the Bluetooth Stack on it but I cannot...
Three questions... We have done some scope testing using DIO markers and it seems to indicate that the pMM SVMHIFG interrupt will interrupt an ongoing flash...
Greetings, I am using IAR IDE 5.40.3 with common components 6.3.11.2079. I have had no issues debugging etc. with other MSP430 variants, but when I connect to...
I want to trigger ADC10 of msp430G2553 from timer A without interrupt ,but my code doesn't make conversation... The sampling rate is 0.2Hz i want to take one...
Does anyone know of design software that uses Android rather than Windows? The same applies for CAD and debuggers? TIA Peter -- Peter Grey Sigma Delta...
Does anyone know if it is possible to speed up startup of the MSP430F5438 chip by increasing the processor speed to 16 mHz in the Lowinit function? I am...
Hi, We're running a program in a while loop and we believe we disable the Watchdog correctly in the beginning. The program runs correctly and never resets the...
I'm in the process of writing something about the MSP430 and spent a couple of hours today looking around at the different tools that are front and center...
This question has probably been answered a thousand times but it's worthy of 1001. You see these wonderful names like TACCR0 and P1DIR or WDTPW or WDTCTL or...
Hi everyone, I'm working on a sensor project which uses TelosB<http://www.memsic.com/products/wireless-sensor-networks/wireless-modules.html> based on CC2420...
I have been trying to get evaluation kits on the Silabs Si4463 but they never seem to be available, although they are listed. Distributors also seem to have...
Hello! I'm working with msp430f2619. I'm using it to sample audio. Fs is equal to 20K Hz, working with 96K B sample. 1) When playing back my low-frequency...
Good morning, We have a device that monitors supply voltage vcc using the built-in supply voltage monitor and causes an interrupt if the voltage falls. The...
Hello! Hope you guys can help me: I just get my fir filter working fine! I'm sampling sound with sample frequency of 10 KHz and using a 128 tap low pass fir...
Hi everyone, I'm working on a sensor project which uses TelosB<http://www.memsic.com/products/wireless-sensor-networks/wireless-modules.html>based on...
Hello everyone, I'm working on a sensor project which uses TelosB<http://www.memsic.com/products/wireless-sensor-networks/wireless-modules.html> based on...
