Hi, We have been having problems with the Autoupdate function with one of our MOD5270 modules. After downloading a program to the module using Autoupdate, the...
Is there a predefined macro for processor variant? Is there a predefined macro in the NetBurner gnuc++ tool chain for processor variant? I know there is a...
Problem solved: Turns out the problem was due to the ethernet driver. I am using 1.99 beta tools. Netburner sent me an updated driver and it fixes the...
Yes all of the Netburner specific hardware platforms have a macro defined MOD5282 defines MOD5282 MOD5272 defines MOD5272 MOD5270 defines MOD5270 SB72 defines...
We want to implement Modbus TCP on a system using a MOd 5282 netburner and currently using the rs232 serial port. Looking for tools and/or experience with...
Hello friends !!! I needed to know whether it is possible to use netburner kit as a BRIDGE or GATEWAY. that is i want to use netburner as a lan to wan or vice...
Addendum: Apologies to Netburner. The problem was not due to the ethernet driver. It turns out that the TIP* signal was being driven low, because one of CS1*...
Hello everyone, I am currently working on MOD5270 and I have trouble generating Interrupts with the UART. In fact, I want the system to Interrupt each times a...
Last fall there was a thread about serving dynamic web pages and one about updating a web page after doing a submit. I wrote up a white paper addressing both...
Hello Tod. From were can I load the example code & web page which is inside the PDF? Can you please send it to me - thanks (better add it to the WEB page as...
I haven't been able to open a trouble ticket at the Netburner support site. I entered the info and set up a password and can log in, but the site doesn't...
... Mark, I've got someone looking at your serial number problem. Your Serial number should be the whole thing including the MOD5213:xxxxxxxxxx If you can...
Paul, I haven't been able to open a trouble ticket at the Netburner support site. I entered the info and set up a password and can log in, but the site...
Well... not normally, but I had to do something to see if anyone was paying attention. :) Yeah that's the ticket... I changed it back to a .jpg in the code...
If you give a mouse a cookie, you better tell 'em where he can download a glass of milk. :) Thanks for the suggestion. I put a link to a zipped file that...
Hi all. I'm new to the NetBurner and Coldfire family, so please bear with me. I'm sure I'll have several questions for you, but just one for now. I'm using...
Hi all, Is it possible to change frequency operation (reducing it) altering the syncr register in mod5282? It is necessary to do it during boot process? Many...
Hi all, No need for answer. If anybody needs, it is possible to change the operating frequency altering RFD bits in SYNCR register without resetting the...
Until someone more knowledgeable chimes in, I can tell you I use port C GPIO on the 5272 all the time and haven't had a problem since early 2003 boards. Also...
The MOD5272 only uses a 16 bit SDRAM interface, the origional poster had a CFV2-66 that uses a 32 bit data bus. You can use the unused data bus pins as GPIO,...
I've downloaded and installed 1.99B for my MOD5213 eval board, and would like to test out the Fat File System with either a flash chip or an MMC card. I found...
Can someone please tell me how to create a 10 micro second and a 1 milli second delay on the MOD 5282. Jus FYI the program that i need this for also contains...
I am not sure you can obtain this precision using OsTimeDly(x) function. You can write a delay routine in assembler. In the user manual you can obtain the...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
