Hi, I have just upgraded a working system from 4.20 beta and a 300 Gb disk (unslinged) to 5.5 Beta. The upgrade went well but: Now I can only boot the nslu2...
... Nope, doesn't look like it's been released yet. ftp://ftp.linksys.com/opensourcecode/nslu2/ contains only R24, R25 & R29. Want me to get on their case? :-)...
<Greg, where did you see this release?> I'm not Greg, but if you navigate down through the Linksys downloads for the NSLU2, select "Firmware", then select the...
... Because the person who asked the question, and received the answer for free, didn't fulfill their part of the bargain and add it to the wiki. See rule #3...
Hi, I read everywhere that i should check that the unslinging process worked and that the rootfs is actually on the disk and not in flash. But I do not seem to...
... Correct. Look at the rootfs and / lines, and ignore the /initrd line. If the size of rootfs and / reflects the size of your disk's data partition, then...
Just a note to correct some incorrect information that was on the list ... Do *NOT* create that symlink. It will be created automatically for you when you...
hi, i'm very newbie. i have installed unslung 5.5 un my NSLU2 i connect in telnet the nslu2 i connect after my usb 80 Gb disk and the nslu2 recognize it i...
Hi I have followed the instructions here http://www.nslu2- linux.org/wiki/HowTo/AttachAFAT32FormattedDrive to attach a FAT32 drive and have nearly got it...
Hi, i have problems with usbdisk and Beta 5.5. I recently was able to get the nslu booting with hd attached with help from this list.(Rod) Now when I don´t...
Did you reboot after unslinging? If not, you still have the flash as your rootfs. If you filled up the flash that way, you should reflash and try again. best, ...
ok, i reflash, format external disk, unsling and.... REBOOT!!! finally, All work fine. This is my mistache: i not reboot after unslinging and the rootfs were...
... That's usually indicative of a corrupted SysConf partition. See the HowTo/ResetSysConf wiki page and see if that works. You will need to fool the slug...
I've just unslung my new slug with version beta 5.5, everything seems to be working fine and working from disk 1 (df confirms my rootfs is in the correct...
I just figured out my problem with apache from my previous post. I followed the instructions in the FAQ for installing apache, but you also seem to need to...
Hi Everyone, I am trying to get a USB hub working with my slug Unslung 5.5. I have an un-powered 1.1 hub with 2 ports that works fine, but when I try a...
In message <dclstm+ma4v@eGroups.com>, paulthego <p.spam@...> writes ... There is no actual need to use the symbolic link method, my personal opinion...
Thanks for the help / tips. I have discovered a bigger problem and that is my rootfs is not on my Hard disk but still in flash so I am going to start again...
I followed the instructions very carefully for upgrading from 3.17 to 5.5. I went into maintenance mode and started the upgrade and my slug is sitting, after...
... Another idea: if you're not using LDAP for anything on your Slug, you could comment out the lines in httpd.conf that include it, and you'll save a bit of...
Hi, I wrote a while back saying that /dev/sda2 seems to sometimes get remounted read-only after the slug has been running for a while. On a punt, I plugged my...
I had a similar question, so I asked both WD and Maxtor(who make the drives I'm using). I've included the responsed below. Perhaps USB/IDE controller in the...
Hi, I am having the same behaviour, I hadn't tried using a memory stick in the second slot, but just did and sure enough the same exact behaviour. I too am...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
