Hi, I am having the same behaviour, I hadn't tried using a memory stick in the second slot, but just did and sure enough the same exact behaviour. I too am...
1925
Todd Zebert
zebertt
Aug 2, 2005 11:13 pm
I had a similar question, so I asked both WD and Maxtor(who make the drives I'm using). I've included the responsed below. Perhaps USB/IDE controller in the...
1924
Dave Hooper
stripwax
Aug 2, 2005 11:03 pm
Hi, I wrote a while back saying that /dev/sda2 seems to sometimes get remounted read-only after the slug has been running for a while. On a punt, I plugged my...
1923
Dale VanZile
lucifer_sam_...
Aug 2, 2005 10:39 pm
... Another idea: if you're not using LDAP for anything on your Slug, you could comment out the lines in httpd.conf that include it, and you'll save a bit of...
I followed the instructions very carefully for upgrading from 3.17 to 5.5. I went into maintenance mode and started the upgrade and my slug is sitting, after...
1920
paulthego
Aug 2, 2005 5:45 pm
Thanks for the help / tips. I have discovered a bigger problem and that is my rootfs is not on my Hard disk but still in flash so I am going to start again...
1919
Robert Hammond
quasi_quixotic
Aug 2, 2005 5:22 pm
In message <PO1z+tB$e67CFwKv@...>, Robert Hammond <rob.hammond@...> writes ... Many apologies, I knew it would line wrap so have re-posted...
1918
Robert Hammond
quasi_quixotic
Aug 2, 2005 5:05 pm
In message <dclstm+ma4v@eGroups.com>, paulthego <p.spam@...> writes ... There is no actual need to use the symbolic link method, my personal opinion...
1917
caplink811
Aug 2, 2005 3:29 pm
... <stuart_riley@s...> wrote: Hi, ... ..or openldap-libs if you don't need the full package. There seems to be a problem with the depencies in the...
1916
tonymy01
thasselh
Aug 2, 2005 3:09 pm
I have one of these: http://www.peridyme.com.au/index.php?fuseaction=product.view&productid=156 That looks (physically) the same as: ...
1915
grahame@...
grahame_falvey
Aug 2, 2005 2:44 pm
Hi Everyone, I am trying to get a USB hub working with my slug Unslung 5.5. I have an un-powered 1.1 hub with 2 ports that works fine, but when I try a...
1914
stuartriley05
Aug 2, 2005 2:44 pm
I just figured out my problem with apache from my previous post. I followed the instructions in the FAQ for installing apache, but you also seem to need to...
1913
stuartriley05
Aug 2, 2005 2:43 pm
I've just unslung my new slug with version beta 5.5, everything seems to be working fine and working from disk 1 (df confirms my rootfs is in the correct...
1912
Rod Whitby
rwhitby
Aug 2, 2005 1:23 pm
... That's usually indicative of a corrupted SysConf partition. See the HowTo/ResetSysConf wiki page and see if that works. You will need to fool the slug...
1911
y99it
Aug 2, 2005 12:43 pm
ok, i reflash, format external disk, unsling and.... REBOOT!!! finally, All work fine. This is my mistache: i not reboot after unslinging and the rootfs were...
1910
Inge Bjørnvall Ar...
inge_arnesen
Aug 2, 2005 11:32 am
Did you reboot after unslinging? If not, you still have the flash as your rootfs. If you filled up the flash that way, you should reflash and try again. best, ...
1909
Mattias
falkon7010
Aug 2, 2005 10:26 am
Hi, i have problems with usbdisk and Beta 5.5. I recently was able to get the nslu booting with hd attached with help from this list.(Rod) Now when I don´t...
1908
paulthego
Aug 2, 2005 1:25 am
Hi I have followed the instructions here http://www.nslu2- linux.org/wiki/HowTo/AttachAFAT32FormattedDrive to attach a FAT32 drive and have nearly got it...
1907
y99it
Aug 2, 2005 1:25 am
hi, i'm very newbie. i have installed unslung 5.5 un my NSLU2 i connect in telnet the nslu2 i connect after my usb 80 Gb disk and the nslu2 recognize it i...
1906
conardcox
Aug 2, 2005 1:25 am
Is the ipkg feed site down? I can't get to it by web-browser or with ipkg....
1905
Rod Whitby
rwhitby
Aug 1, 2005 10:14 pm
Just a note to correct some incorrect information that was on the list ... Do *NOT* create that symlink. It will be created automatically for you when you...
1904
Rod Whitby
rwhitby
Aug 1, 2005 10:03 pm
... Correct. Look at the rootfs and / lines, and ignore the /initrd line. If the size of rootfs and / reflects the size of your disk's data partition, then...
1903
Mattias
falkon7010
Aug 1, 2005 10:00 pm
Hi, I read everywhere that i should check that the unslinging process worked and that the rootfs is actually on the disk and not in flash. But I do not seem to...
1902
Rod Whitby
rwhitby
Aug 1, 2005 10:00 pm
... Because the person who asked the question, and received the answer for free, didn't fulfill their part of the bargain and add it to the wiki. See rule #3...
1901
Mattias
falkon7010
Aug 1, 2005 9:50 pm
Hi and thanks, the second hint worked like a charm.. Why does the information not exist in the FAQ? Best regards Mattias...
1900
caplink811
Aug 1, 2005 2:54 pm
... Hi, ... it is ... 1st hint: http://www.nslu2-info.de/showthread.php?t=3134 2nd hint: http://groups.yahoo.com/group/nslu2-linux/message/7489 bye JrB...
1899
John Rotert
seventy_five...
Aug 1, 2005 1:49 pm
<Greg, where did you see this release?> I'm not Greg, but if you navigate down through the Linksys downloads for the NSLU2, select "Firmware";, then select the...
1898
Philip Johnson
tuxatemyfavo...
Aug 1, 2005 1:12 pm
... Nope, doesn't look like it's been released yet. ftp://ftp.linksys.com/opensourcecode/nslu2/ contains only R24, R25 & R29. Want me to get on their case? :-)...
1897
Mattias
falkon7010
Aug 1, 2005 11:04 am
Hi, I have just upgraded a working system from 4.20 beta and a 300 Gb disk (unslinged) to 5.5 Beta. The upgrade went well but: Now I can only boot the nslu2...
