I just spoke to linksys and managed to resolve the problem with slow performance after the upgrade. Apparently you need to do a reset of the NSLU2 by holding...
... True, unless you buy regular IDE drives and separate USB adapters and set them up in a regular PC first. ... Depends on your usage pattern... if it's truly...
... I think I replied to this already but it didn't seem to take... anyways, take a closer look at your httpd.conf file. Mine has a <IfModule prefork.c>...
... Can you show your httpd.conf? There's some other sections in there that affect that... mine has something that looks like this: <IfModule prefork.c> ...
... echo works fine. ... I do believe you are correct. Although I put my cout statement just at the start of main, I put it after the variable declarations...
Just looking at getting the LaCie 300GB d2 drive (Firewire400/800, USB2, 7200rpm, model 300791). Has anyone tried this particular drive with the Slug? (The...
Hi, I would have a good look as to the cooling of the harddisk. I blew two LaCie 160GB drives due to overheating (24/7). Good luck, honestly:) My advice: pick...
Thanks for your reply Philip. I know that ctorrent is console based, but as it is available for the nslu2 ... I was hoping. About writing the pages, yes it is...
... Well, I was just going to try, since I also wish to download RTSP streams but at least one issue is with cook.so codec, needed to decode most of rtsp...
Irfan, I suspect the problem is not with the NSLU2, but with your network. I've seen similar delay problems with my employer's network, where we have several...
I don't believe this as a statement of fact. You're saying here that if the drive is idle all night then spinning it down will actually increase the life of...
I tried this but the problem stays the same. FYI, the unit responds to the "ping" immediately. The long delay is in browsing the shares. Once the file transfer...
Thanks Stewart. The network is moderately simple and consists of 1 (broadband router+4port switch), 2 more switches, 1 server and about 12 workstations. The...
Hi Martin, I have *not* had good experiences with LaCie d2 320GB drive(s) (i.e. older, discontinued model) The first one, bought in November 2004, lasted 6...
Hello irfan29200, ... The following might not be useful in your case, but worth a try. Hence I thought I let you know anyway. Your situation reminded me...
... I've used two different generic 2.5" USB-powered enclosures I purchased on eBay. Both were equipped with used 20 and 30GB older IBM 2.5" drives (the ones...
Hi, I wonder if anyone can help with this. I'm trying to write a fairly large file (2.6Gb) to my NSLU2 but I get an error that I'm out of disk space despite...
Hello, I do not know if this is the problem, but we are having problems with Linux and a 2 GB file size limitation here at work. We are using Red Hat ...
The problem is that brushless or not, they are still mechanical moving parts. These wear down over time. It turns out that at times, spinning up a drive can do...
Mike, Would you mind sending me the binary you have compiled for using Cherokee. I wanted to set up NSLU2 mainly for serving to my ShowCenter and also as a...
... I have the same setup, 2 Lacie Porsche 250GB drives attached to my slug, stacked, in my stereo cabinet. How long did it take before your disks failed?...
... Sure, the file is availible at: http://www.thewinters.org/php-fcgi.tar.gz You'll probably need the whole PHP package installed as well. Just a note,...
Hmmm, you seem to be having the same issue that I originally had - very slow browsing of the shares. This is with the latest LinkSys R6 firmware right? This...
... got ... about ... anyone ... instructions. ... AlienBBC ... Would it be possible to provide a detailed step by step guide, or possibly better still upload...
I see that the MySQLdb python module is not yet available for NSLU2 (it requires compilation), so I'm wondering if any users here might have already done that...
... Mike, Thanks for your info and help. - I have PHP package installed, I will try your binary when I get home. - I am using tRIO 1.5 for the RIO. Though I...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
