Hello everybody. I just created my website on NSLU2 based on HowTo from nslu2- linux.org "SimpleHomeWebsite". I don't think my router allowes to map one port...
Hello Douglas To get bluetooth up, I based my method on that found at http://bluez.sourceforge.net/contrib/HOWTO-PAN Preparation: Packages you will need (there...
Hi all, First, I would like to thanks all the NSLU2-Linux community for the huge and great job ! Currently, my slug is used as following: - uNSLUng 5.5 beta -...
Hello ... "ipkg install thttpd" And some changes in thttpd.conf (in /etc/init.d or /opt/etc/init.d). You will have to tell thttpd where to look for your MP3. ...
10-4 _____ From: nslu2-general@yahoogroups.com [mailto:nslu2-general@yahoogroups.com] On Behalf Of Laurent Gilson Sent: Wednesday, February 01, 2006 11:23 AM ...
... new Yahoo! Security Centre. http://uk.security.yahoo.com ... Roland, Thank you for this reply. I'm very greatful. Have you used this configuration with...
Hello Douglas, I connect my iPaq to the slug with the technique I described. I have to use what on my iPaq is called the "Bluetooth Manager". I create a new...
Hello , I have strange problem. Since yesterday, for any request apache responds Forbidden You don't have permission to access / on this server. Apache/2.0.54...
I found the last properly accessed page. ~ # cat /www/tools/who.php <?php // outputs the username that owns the running php/httpd process // (on a system with...
I'd like to be able to access the data on my slug over the internet. If I forward the router port 20-21 to the slug I can access the data via ftp. If forward...
I do this with a combination of openssh on the slug fuse and sshfs on the client References: http://www.nslu2-linux.org/wiki/HowTo/UseOpenSSHForRemoteAccess ...
Perhaps I should have mentioned... The slug is running the Linksys firmware (R63) and the client machine will always be Windows. Simon ... internet. ... data ...
Unless you load something other than Linksys firmware and run openvpn the only thing I can think of is buy a VPN router and set up a tunnel between the NSLU2...
Hi, You can open the SMB port on your firewall/router, but that would be kind of risky. Or call it st*p*d:) Yes, the best normal practice would be to buy a...
Oops... I assumed you were running either unslung or openslug, sorry. The stock Linksys firmware can only export Windows shares. While possible, it is not a...
Hi! I've installed vsftpd and it works. But I only get between 40kB/s and 70kB/s when uploading to the external USB drive. Any idea what could be wrong? My...
... Roland, Much of what I'm reading suggests that iPaqs don't support the full Bluetooth protocol stack. Specifically NAP access. What kind of iPaq are you...
Simon, I run Unslung 5.5 with Samba shares which I share over the net. I run Windows XP on my work box. I opened port 22 (SSH) in my firewall which forwards to...
... I've never used vidcat, but according to "man vidcat" at http://linux.com.hk/penguin/man/1/vidcat.html you can specify an alternative device using the -d...
You may have IIS set up to use an anonymous user. This allows an anonymous user to browse to your website, however, any authetication is done as IUSR_Machine...
Check to see if you have read permissions for public on all the files you need. Just to be sure, run this command on your document root. chmod -R 777 ...
Hi all I had a Maxtor DiamondMax Plus 9 hard disk hooked up to my NSLU2 for a couple of weeks before it mysteriously stopped working. Unfortunately it was a...
Yep, same problem here! I'm also finding that the torrent file sizes are incorrectly reported. I found some references to this happening when certain compile...
3739
Vincent Fare
Vincent.Fare@...
Feb 2, 2006 8:54 pm
Hi ! Yep for my part too, it's the best solution. Except that I tried to install it on a synology DS 101, and it seems to be impossible just because of the...
Hello Douglas, I've successfully tried the NAP stuff with an h2200 iPAQ and an h4700 iPAQ. Both of these run PocketPC 2003. I don't know anyone with an 1945...
