Loaded unslung-standard-2.14. Installed/Upgraded packages for Busybox and others. I to hate the name DISK 1 and tried to change it to Public in the file...
... I briefly used the Twonky server with a Netgear MP101. The MP101 kept dropping its wireless connection, so I returned it. However, for the 1-2 weeks I...
Hi there, I know there are other posts regardings this subject, sorry that I have to bring it up again. The starting point was an article in the current issue...
The NSLU2 stops showing up under the Network as seen from a Mac laptop. It used to work fine (minus a quirky reliance on an XP system). This NSLU2 is running...
... What happens if you try to send a ping to the NSLU2s IP-adress? Do you get any response? I am not that familiar with Macs but normally you should be able...
I just recently had a power outage after which my slug would only half boot as you described. After nosing around, I found it was the upgraded busybox causing...
With windows and a clock, I measured about 4-5 MBytes per second transfers. The low end was with large quantities of 4MB MP3 files. The upper end of the range...
... Yes it works fine in other ways and shows up under winXP (SP2) in the network neighborhood. It was showing up on the Mac laptop under the quirky conditions...
I just got my NSLU2 today and got it set up. I have a WD 250 GB drive in an OWC Mercury FW/USB enclosure. The utility came up and asked about formatting I said...
suse 9.2 with firewall off I can access the slug and folders . when I turn firewall on I can see the slug in windows worg group and the folders in in. but I...
I'm getting 100-400 KB/sec for a 300 meg file. I've tried saving from the http site and from windows explorer. I'm connecting to a netgear WGT634U then...
I had the same problems right after upgrading firmware. I power cycled the NSLU2 and now it is back to it's normally slow 405 MBytes per second. Mark S....
I am sure you figured it out by now. I have 2 of the Maxtor 300G drives. The drives format and work perfectly, but the built in backup utility will not work....
What size are your disks? > 250G? Had the same problem with 300G disks. Seemed to create a few shares then think it was done. Called Linksys, backup can't...
Any ideas? This is pretty weird (although it's always happened for me, so I wonder if it's a feature that I just don't understand) The NSLU2 manual states...
Thanks. I was about to throw the thing in the trash. I turned it off before bed and everything was better in the morning. I'm getting 2.5 MB/s over my...
I just installed NSLU2 and downloaded the latest firmware without checking e g this newsgroup and (as other here reported) have a lousy thruput (128KB/sec). ...
I am using unslung 2.12 and have two 160 GB disks. Backing up disk 1 to 2 takes a few seconds according to the log. However, looking into the script...
http://slugbug.nslu2-linux.org/bug.php?op=show&bugid=2&pos=0 In summary, the Linksys drive backup program can't backup symlinks, and there is no fix (other...
Well with no help from Linksys I still have no clue on how to set up the NSLU2's Internet File Server so that I can access the files from the internet. Any...
hello I'm new to palying w/the NSLU and can not figure out how to edit the mt-daapd conf file. I followed the tutorial at nslu2-linux.org and have the server...
... If you are behind a router, forward port 80 to the internal IP address of the NSLU2. Then, you can access files on the NSLU2 with the web interface. HTH, ...
I have a LaCie Porsche 250GB UBS2 disk connected to my NSLU2. I can't get the performance above ca 150KB/sec. Have tried with both 2.3.25 and 2.3.24 version...
Maybe a bit late to reply, but I just got the same problem. The only tool I found who could "see" my lost files was Stellar Phoenix Recovery for Linux (runs...
Hi there, I ran into a problem with my NSLU2. I was at about 30G of used disk space out of 200G in an ADSTech DLX-185 (Firewire/USB) enclosure when I got a...
In order to get the backup working from disk 1 to disk 2 under unslung 2.12 I installed rsync and modified /usr/sbin/drivertodrivercp to use it. Here's the...
... Normally, the reason for things failing in crontab when they work on command line is due to the very minimal environment variables that crontab sets up...
... Actually, the first four lines of /etc/crontab read: SHELL=/bin/sh PATH=/sbin:/bin:/usr/sbin:/usr/bin MAILTO="" HOME=/ So the environment should be...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
