I'm trying to set up a RAID 1 array on my slug, something I did before with another slug. For some reason that I can't seem to figure out, on a reboot the...
8261
Rajesh
rajeshh_98
Nov 20, 2010 8:00 am
hello: I have an unslung nslu2 that uses a flash drive ( maybe 2GB) for a few years. Just last week, I found it was out of space somehow, and the electricity...
8262
rolandkbs
Nov 21, 2010 11:44 am
Hi Probably the drive went full, because over the time all free space was used by reallocated bad blocks. However. I wold try the following: 1. put the flash...
8263
karim kanso
cskarim@...
Nov 23, 2010 4:33 pm
Hi, I have been using the optware for a mybookworld blue ring host, and its been good. One issue I have come accross: The default configure options for ffmpeg...
8264
miles.sara@...
miles.sara...
Nov 25, 2010 9:46 pm
Hi, I installed minidlna from optware on my unslung nslu2. It downloaded, built and installed fine, but when I start it, I get the following: #...
8265
Peter Campion-Bye
peter_bye
Nov 29, 2010 9:48 am
My 'install Bundle::CPAN' has been running for over 4 days now, does anyone have any idea how long it will actually take? The slug is de-underclocked (266...
8266
Ingo Flaschberger
chaoztc
Nov 29, 2010 10:11 am
Dear Peter, ... installing to usb takes really long - try to install at a hard disk and also swap to disk. copy whole system to disk and then back: raw: dd...
8267
Peter Campion-Bye
peter_bye
Nov 30, 2010 8:06 am
On Mon, 29 Nov 2010 11:10:50 +0100 (CET), Ingo Flaschberger <if@...> ... Thanks for the suggestion Ingo, I transferred the contents of the USB stick to a...
8268
kevvap
Dec 1, 2010 10:09 pm
Hi, I have a NSLU unslung and have a problem with man pages, they simply show up as blank. I have groff installed , can't seem to figure out what it could be....
8269
mspohr
Dec 2, 2010 1:37 am
I successfully installed the 6.10 beta package using upslug2. It verified and rebooted. However, now I can't access the web interface on my NSLU at...
8270
Paul Marwick
pmarwickuk
Dec 2, 2010 9:08 pm
I have a NSLU" which was unslung to a 512mb flash drive a couple of months ago. It is used to connect a Toppfield Freeview PVR to the network. Doesn't get a...
8271
Mike Westerhof
mjwest61
Dec 4, 2010 2:15 pm
First thing to try is to follow the steps to enter "upgrade mode" (use the reset button method on the wiki) -- and once you see the correct pattern in the...
8272
Mike Westerhof
mjwest61
Dec 4, 2010 2:18 pm
Did you previously change the port number for the web server? Unslung will honor the saved port number setting, so look for the web server at the original...
8273
dad2luke
Dec 4, 2010 5:36 pm
Hi All, I was curious what the symptoms are of a dead battery. I have a NSLU2 (running R63 of the COTS software), and it always hangs on the first boot. The...
8274
Mark Spohr
mhspohr@...
Dec 4, 2010 6:50 pm
I finally installed SlugOS 5.3 on it and was able to ssh into the system. I'm still confused about what happened with the unslung 6.2 and no web access since I...
8275
Mike Westerhof
mjwest61
Dec 4, 2010 7:27 pm
Primary (and only as far as I've ever observed) symptom of a dead on-board battery is that the time is always wrong after it's been powered off for a while. ...
8276
Mike Westerhof
mjwest61
Dec 4, 2010 7:39 pm
Indeed, it would be nice to have some way to ensure that everything is reset -- there is a wiki page on how to clear or reset your sysconf partition, but...
8277
Paul Marwick
pmarwickuk
Dec 5, 2010 1:23 am
... dug out a new (short) cat5 cable and connected it to the router. At which point, it booted normally..... Grr.... ... Having (painfully) pulled out the 10...
8278
Mark Spohr
mhspohr@...
Dec 5, 2010 5:10 pm
Thanks for this detailed answer. I had guessed that there was a good reason for keeping the old settings but had no idea it was this complicated to reset the...
8279
dad2luke
Dec 13, 2010 5:42 am
... I replaced the battery and everything seems fine now. But I am deeply curious what it is so hard to open the case when there is a battery inside that will...
8280
Bill
docbillnet
Dec 13, 2010 1:57 pm
Like most modern electronics it is designed to be as much "throw-away" as possible. Manufactures do not want you doing things like replacing batteries that...
8281
reuter.rudolf
Dec 13, 2010 4:14 pm
... I have a portable drive I've been trying to figure out a way to open for two years now without breaking anything. Mainly because I'm curious if it is...
8282
dad2luke
Dec 13, 2010 6:54 pm
... I have two NSLU2's since the NSLU2 uses a UNIX file system and I don't own another UNIX machines. So I need a spare. I have overclocked one and am seeing...
8283
JaskaJ
jokunenjaska...
Dec 13, 2010 10:32 pm
Hi, I need to get debian etch (4.0) to my nslu2. Where it can be downloaded? (My weather station software wont work newer releases..) Thanks, Jussi...
8284
Paul M
pmooney22
Dec 14, 2010 3:41 pm
http://cdimage.debian.org/cdimage/archive/ Disclaimers: I have entered into no agreements regarding mails erroneously sent to this address, and reserve the...
8285
JaskaJ
jokunenjaska...
Dec 14, 2010 4:49 pm
Thank you, But I dont find nslu2 image? (like these http://www.slug-firmware.net/d-dls.php )...
8286
beerman_wendel
Dec 17, 2010 7:32 pm
Hello, I got an arduino microcontroller which I want to use to control my slug with. I installed kernel-module-usbserial kernel-module-ftdi-sio But no...
8287
Carl Lowenstein
cdlowenstein
Dec 17, 2010 7:34 pm
On Fri, Dec 17, 2010 at 11:32 AM, beerman_wendel ... Simple question: is the USB device connected? carl -- carl lowenstein <clowenstein@...>...
8288
beerman_wendel
Dec 18, 2010 7:55 am
Yes, it is connected. Rigas...
8289
reuter.rudolf
Dec 18, 2010 8:59 am
Hello Rigas, I have written a setup documentation for an USB-RS232 interface: http://www.rudiswiki.de/wiki/NSLU2SlugOS48 Hopefully it will help you. Regards,...
