... I can see the networked drive on two separate branches: My Network Places\Entire Network\Microsoft Windows Nwtwork\Workgroup\LKG7CDC26 or My Network...
856
mensandre
Feb 19, 2005 6:32 pm
Hi Today I wanted to connect to my NSLU with release 3 on it but I couldn't connect. After I looked at it I noticed the ethernet led wasn't on. So I powered...
857
Astro Jetson
astro_jetson_jr
Feb 19, 2005 10:42 pm
... Motorola cable modem that I have also includes a router. I have ... Did you try pings using the IP address? www.google.com is 66.102.7.99 (well ONE of...
858
j_o_h_n_d_p
Feb 20, 2005 2:56 am
This worked perfect!! This now conection is now rock solid and i can now transfer files larger than 100k. The web configuration tool now works perfectly and...
859
Spencer Shearer
spencershearer
Feb 20, 2005 10:11 pm
As far as I could tell the settings on my slug were correct. So I unpluged my Motorola router and plugged in my Linksys router and everything is working well...
860
unix fan
unix_fan
Feb 21, 2005 12:56 am
I went to update the wiki based on the current discussion. Seems like Question 27 in the FAQ addresses this topic already. ...
861
Todd O. Klindt
tklindt
Feb 21, 2005 1:44 am
Could you edit it to read that shutting uPNP off on the NSLU2 and the DLINK will increase the reliablity? Some folks have shut off uPNP on just the NSLU2 and...
862
unix fan
unix_fan
Feb 22, 2005 2:21 am
Consider it done - my first wiki update. Check out the update to the FAQ, question #27. Hopefully this will save some Dlink 624 owners time and frustration. ...
863
realpsychodad
Feb 22, 2005 8:01 am
Hi Has anyone tried the server for the Hauppauge mediamvp (Video streaming client). ipkg vdr-mediamvp works ok, but when starting mediamvp I get only...
864
windsurfingdude101
windsurfingd...
Feb 22, 2005 4:27 pm
I have just installed unslung onto the nslu2 and I am following the instructions to unsling to a drive. However having not used telnet before I have come to...
865
Tom Gross
thomas144
Feb 22, 2005 4:40 pm
You need to log into your slug as root. At the telnet prompt you need to type "root" and then a password of uNSLUng (I think). Be sure to change that...
866
windsurfingdude101
windsurfingd...
Feb 22, 2005 4:58 pm
Thank you for your help. Have managed to do it now. Yes I am a newbie to Linux, but I enjoy a challenge! I have done the unslinging (went through the process)...
867
Tom Gross
thomas144
Feb 22, 2005 6:05 pm
If you have a harddrive attached to drive one, from inside the slug on your root account, you should be able to "cd" to /share/hdd and see two directores: data...
868
windsurfingdude101
windsurfingd...
Feb 22, 2005 6:17 pm
Ah, so they are only visible through telnet not windows explorer. Do I have to disconnect the harddrive and telnet to the nslu2 using root and then reconnect...
869
Tom Gross
thomas144
Feb 22, 2005 6:33 pm
I don't even know if these directories are visible through windows explorer on your administration page. No, you don't have to reconnect your harddrive ...
870
windsurfingdude101
windsurfingd...
Feb 22, 2005 8:14 pm
I shall do the password stuff tomorrow. Hoping to use it as an ftp server, bit cheaper than a buffalo diskstation. Thanks for your help tom....
871
Tom Gross
thomas144
Feb 22, 2005 8:20 pm
surfingdude, I just realized I said "change the root password with the root command" - I meant the "passwd" command. good luck! -Tom ... === message truncated...
872
Tim Lewis
virtualctor
Feb 23, 2005 3:53 am
... And the NSLU2 and your computer are definitely in the same workgroup? ... There's a method for doing this, but I was unable to locate a page explaining it....
873
Tim Lewis
virtualctor
Feb 23, 2005 4:23 am
... May I make a suggestion? Set up SSH instead of FTP. You can use SSH to transfer files like you do with FTP (using SFTP), and it has a few advantages...
874
haakies
Feb 25, 2005 1:21 am
I am also concerned about the temperture of my harddisk. It is not getting very hot from the outside but, I also would like to have a option to put my harddisk...
875
dnaman43
Feb 25, 2005 2:01 am
"Not getting very hot on the outside" doesn't necessarily mean things are good. It means either: (a) the heat is being transmitted to the case but losing it...
876
John
raistlin0044
Feb 25, 2005 2:41 am
Hey Mike, Did you ever get this resolved? I have almost the same issue. Mine does recognize the drive on port2 but not port1. If I try to format the drive...
877
donna foley
dontbfooled2000
Feb 25, 2005 8:22 pm
My PC sees on the network the Linksys DISK1 and ADMIN1. When trying to access ADMIN a name and password window appears. None of the default passwords.....ADMIN...
878
haakies
Feb 25, 2005 9:39 pm
i have a e-tech modem. When i put my web-server IP (192.168.1.50) into the DMZ of port forwarding and put ping-mode on everything works fine. When i replace...
879
Adrian Day
nslu2_haxxor
Feb 26, 2005 1:13 pm
On Fri, 25 Feb 2005 20:21:58 -0000, donna foley ... Username: admin Password: admin Works for me. BTW, it's case sensitive....
880
ted_to
Feb 27, 2005 11:24 pm
Hi, I've installed CUPS but can't seem to get to the web interface and XP does not allow me to install a network printer. Did I forget to do something? Any...
881
Inge B. Arnesen
inge_arnesen
Feb 28, 2005 10:32 am
NSLU: Is the server running (ps ax |grep cupsd)? Can you connect to the port locally using telnet (telnet localhost 631)? Also, looking in error logs is...
882
ted_to
Feb 28, 2005 3:40 pm
... # ps ax |grep cupsd 605 root 628 S /opt/sbin/cupsd 643 root 404 S grep cupsd So, yes, it is running. ... I'm not sure exactly what it is...
883
scottkal
Feb 28, 2005 8:01 pm
My NSLU2 is updated to 2.3 Release 29. I have it set to reboot each day. It's been running for a few weeks since the update just fine. Today, she's not...
884
quasi_quixotic
Mar 1, 2005 1:03 am
... I am also interested in the answer to this question. My understanding is that the firmware is a Linux core plus Samba2. So should be easy to do, probably...
