Hello, An update on using Bluetooth. I need Bluetooth on optware NSLU2. I could not pair devices. However I installed the bluez and not the bluez2 library and...
Hello, I (plan) to use bluez on optware. I also nee rfcomm to get the whole working. However installing rfcomm (ipkg install kernel-module- rfcomm ) version...
... Be aware that bluez2-utils is actually *older* than bluez-utils. The '2' refers to version 2.x of bluez - bluez is now up to version 3.x, but I have not...
... I ... the ... not ... pairing ... 2), ... The ... 3.x, but ... successfully ... utils ... Rod, Did you also install rfcomm? I need this because of asterisk...
... DHCP ... I once used Ethereal (now Wireshark) in promiscuous mode to find the IP address of a recalcitrant slug that I bought off eBay. (The seller said it...
I once used Ethereal (now Wireshark) in promiscuous mode to find the IP address of a recalcitrant slug that I bought off eBay. (The seller said it was in...
Hi Rod, I used the wiki Obese instructions wiki/HowTo/ObeseSlug and I modified that to make my own RedBoot (from my RedBoot) - is this different than your ...
I´ve installed slimserver 6.5.4 using the optware package (ipkg install slimserver). The result was hopefull, yet not completely succesful: * package...
... Why would you like to run mplayer on unslung? It doesn't have an output device and it's to slow for most things mplayer can do. -- Marcel Nijenhof Optware...
... It also has no floating point unit. I have found some integer-based mp3 players, but trying to do video without the FPU is probably futile. beww...
... the IP ... 10.0.0.x.) ... reflash ... fixing it ... disk). Thanks for the tips - no dice with etheral (nslu2 being quiet as a mouse unfortunately), but...
Hi, unfortunately I cannot tell you how to compile mplayer on unslung, too, but it works like a charm for slugos/be. As it uses libmad for decoding mp3s there...
Hi, Finally I could make my Slug running properly with Unslug and the packages Xinetd + Samba2 + Fuppes as I was expecting (Xinetd to have permanently TELNET...
The standard nslu2 image built by openwrt includes apex as the second stage bootloader. Just flash it with upslug2, find out which dhcp address it acquired...
Hi Rod, Back from gardening in between two Slug works... MORE painfull gardening... lol... Many thanks for your quick reply, I'll follow your advise and will...
Hello, Pierre. I assume you know that once you put on a 16MiB flash, you'll be unable to get your old flash contents directly, unless you have a flash...
Hi Rob, Many thanks also for your advise, I wasn't aware of the risky stuff by just replacing the 8MB flash with a 16MB one. I thought it was just a question...
Again, I will try to install LCDproc with HD44780 on I2C bus. "FATAL: Module rtc_dev not found. Setting the system clock.. Cannot access the Hardware Clock via...
Hi Rob, I got the 10 oz of vodka and the rest... lol... My concern now is I cannot get out from the DHCP as far I see my fixed address when I type "uci show...
Hi, Pierre. My apologies, I don't use unslug, I've only used debian slug mostly. For these kinds of questions, you might have more luck on the nslu2-general...
Hi Rob, No no, when I said "I got the 10oz of vodka and the rest..." it's because I booted Openwrt! At the serial console port there is a funny pleasant...
If you built openwrt yourself, it will have apex. I don't remember whether the latest binary release uses it or not. Once you have apex, you can change it's...
Hi Rod, I installed Openwrt, openwrt-kamikaze-nslu2.bin (Kernel Linux 2.6.21.6) and when I boot with a ctrlC after the + I go into Redboot, I don't see APEX ...
Hi Pierre François, Happy to read you! If you look at the boot log, you must see something like this : *RedBoot(tm) bootstrap and debug environment [ROMRAM] ...
Hello, group. I just finished going through and updating the Wiki instructions for CentOS, and everything seems to build fine. Except I need to replace the...
... I believe that 1.5.13 can detect both cases. ... Yes, this is the way you can intentionally limit it to 64MB. ... Then use use the setenv command on the...
... Try just: slugimage -F -p -o test.bin -L apex.bin -k vmlinuz -r Flashdisk If that works, then start adding options until you find the one that breaks it. ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
