Hi there, I have a system that is unslung to a memory stick on disk 2. Disk 1 is a large data hard drive which I use for many things including backup of disk...
22233
linuxrouter
jeroenmoetwil
Sep 2, 2008 8:17 am
I managed to find a solution to my problem. The microcode loading issue was related to udev, which is fixed now. Both NPE-B and NPE-C load correctly. The MII...
22234
Rod Whitby
rwhitby
Sep 2, 2008 8:24 am
... The NSLU2 kernel does not use the ixdp425-setup.c file. MII port allocation is done in the nslu2-setup.c file in the mainline kernel. -- Rod...
22235
Drew Gibson
green.ogre
Sep 2, 2008 6:56 pm
Hi, my slug, running UnSlung (V2.3R63-uNSLUng-6.8-beta), recently started flashing the status/ready light constantly. I can connect via SSH, web interface,...
22236
sp00nage
Sep 3, 2008 9:30 am
Hi All, I have been lurking in this list for a few weeks now but this is my first post. I recently used a SLUG running asterisk to solve an interoperability...
22237
dhascome
Sep 3, 2008 11:29 am
Hi all. I've just bought a NSLU2 and currently now I've a Debian inside and also it's overclocked, so I wanna make the next step: to fatten it. But I have a...
22238
phiho_251286
Sep 3, 2008 12:17 pm
hi all! I have install debian in my nslu2. I use upgrade utility to upgrade for this version. After upgrade, i can't telnet to nslu2, i have use winscp to...
22239
Martin Michlmayr
mmic1979
Sep 3, 2008 12:36 pm
... If you installed the Debian installer, you have to connect as installer with the password install Which image did you upgrade to exactly? -- Martin...
22240
Pierre-François (...
f5bqp_pfm
Sep 3, 2008 12:41 pm
Hi Richard, To fatten your slug you should find 16 bits chips like this: MT48LC32M16A2 - 8 Meg x 16 x 4 banks from Micron or equivalent from other...
22241
Pierre-François (...
f5bqp_pfm
Sep 3, 2008 1:00 pm
Hi again Richard, I've forgotten to tell you that you can find PC133 barrels with 64M chips ant it wont work either! If you don't find used the good memory...
22242
phiho_251286
Sep 3, 2008 1:51 pm
... upgrade ... connect ... no no! i need password for debian install by manual method. in this case i have try with pass is root, have any pass for this case?...
22243
Martin Michlmayr
mmic1979
Sep 3, 2008 1:54 pm
... Yeah, root/root in this case, but iirc the manual methods always does DHCP. So maybe you have the wrong IP address - check on your DHCP server. -- Martin...
22244
phiho_251286
Sep 3, 2008 2:44 pm
... Hic! So what could i do to now. I have set IP at two case. Firt, i chose DHCP for my network, and i ping to 192.168.1.77 but this action is not respone,...
22245
Martin Michlmayr
mmic1979
Sep 3, 2008 2:52 pm
... As I tried to say, the manual installation of Debian/NSLU2 is configured to use DHCP, not the static address 192.168.1.77. If you have a DHCP server on...
22246
phiho_251286
Sep 3, 2008 4:15 pm
... Dear Martin Michlmayr. Thank you for helpful about this problem. I have tried with method you say, but still connect nslu2... At this time i have reflash...
22247
Gordon Farquharson
gordonfarquh...
Sep 3, 2008 4:43 pm
... Which upgrade utility did you use? Was it 'apt-get dist-upgrade'? Gordon -- Gordon Farquharson GnuPG Key ID: 32D6D676...
22248
phiho_251286
Sep 3, 2008 4:52 pm
... No! I use sercumm utility in windown to upgrade debian....
22249
Gordon Farquharson
gordonfarquh...
Sep 3, 2008 4:53 pm
... The flash memory in the NSLU2 can be flashed 100000 times, so I wouldn't worry about damaging it. Gordon -- Gordon Farquharson GnuPG Key ID: 32D6D676...
22250
Martin Michlmayr
mmic1979
Sep 3, 2008 4:54 pm
... Why don't you use the installer rathen than the manual method? The installer is much easier. -- Martin Michlmayr http://www.cyrius.com/...
22251
Gordon Farquharson
gordonfarquh...
Sep 3, 2008 4:55 pm
... You need to be more specific for us to be able to help you effectively. What image did you upload to the NSLU2 using the Sercomm utility? Was it an...
22252
phiho_251286
Sep 3, 2008 4:59 pm
... Yes! Before, i have try this method(use installer), but after install i can't telnet into nslu2 because pass login invalid, i try with user "root" and pass...
22253
Gordon Farquharson
gordonfarquh...
Sep 3, 2008 5:04 pm
... Martin is correct - use the Debian Installer installation method. It is much easier. However, first, I'd suggest flashing the Linksys firmware to your...
22254
Gordon Farquharson
gordonfarquh...
Sep 3, 2008 5:06 pm
... At some stage during the installation process with the installer, it will have asked you for a root password. Use the password that you set at this stage...
22255
phiho_251286
Sep 3, 2008 5:17 pm
... yeah. i have install debian with installer method by web interfaces: http://www.cyrius.com/debian/nslu2/install.html, after install my nslu2 reset again. ...
22256
Martin Michlmayr
mmic1979
Sep 3, 2008 5:26 pm
... The test you're quoting tells you what the password is - install. -- Martin Michlmayr http://www.cyrius.com/...
22257
jvikezz
Sep 3, 2008 5:26 pm
I was wondering if anyone has solved the spindown issue? if yes, then what was the approach? I run unslung 6.10 with an Western Digital 500 GB Elements USB...
22258
phiho_251286
Sep 3, 2008 5:30 pm
... yeah. i try with pass is "install" but it still invalid....
22259
Gordon Farquharson
gordonfarquh...
Sep 3, 2008 5:32 pm
... So, during the installation, did you set a both a root password and a user name and password? If you did indeed do this, then use either the root password...
22260
phiho_251286
Sep 3, 2008 5:47 pm
... you set ... this ... oh no! I think have a problem with my nslu2, now i can't upgrade mode for it. Why?...
22261
Gordon Farquharson
gordonfarquh...
Sep 3, 2008 5:52 pm
... http://www.nslu2-linux.org/wiki/HowTo/UseTheResetButtonToEnterUpgradeMode -- Gordon Farquharson GnuPG Key ID: 32D6D676...
