If you can love the slug you can love the plug.  A stock plug is comparable to a
beefed up slug running Unslung.  Probably the best plug is the 1.2 GHz V2, which
can run Debian Squeeze nicely (and last cost me less than $20).  It has 4 USB
and 1 GbE port. See http://forum.doozan.com/ , they have discussions about the
different plug variants.  I have one that has been running continuously since
2009 on a UPS.  Gets warm but not hot.  V4s have external power supplies, are
slower, but have IDE and USB3 ports.  Their CPU probably gets warmer due to less
ventilation.  Basically, an ARM is an ARM is an ARM.  Buy whatever suits you
whether it is the Pi, Beagleboard, or Plug and put whatever you want on it. 
Just remember to love your slug and replace its power supply every few years.

--- In nslu2-linux@yahoogroups.com, "harshbaste" <harshbaste@...> wrote:
>
> Hi,
>
> I've had an NSLU2 for a good 4 years now and was just taking a peek at the
other offerings of similar devices.
>
> One of the kits I was looking at is the Pogoplug Series 4. Does anyone on this
channel have any extended experience with it. In particular :
>
> 1) Whats its power consumption like compared with the NSLU2?
> 2) Is it as reliable as the Slug?
> 3) Does it have any overheating issues?
> 4) Is it worth the trouble switching over in general? Is OS support mature
enough on it to run Debian Squeeze with full functionality of all I/O ports e.g.
> 5) Is there any other platform that is perhaps better than the Pogoplug Series
4?
>
> No way I'm going to give up on the NSLU2 - its got a VW Beetle like aura about
it so I'm going to keep it indefinitely :). But hardware failures do happen and
I have to consider alternatives for the future.
>
> cheers,
> H
>

Hi all

I read on DD-WRT website this Modem/router is supported device
with Atheros chipset.
I read something here
http://g300nh.blogspot.fr/2010/06/software-installation-on-dd-wrt-part-1.html
about the WZR-HP-G300NH and it seem same device except the modem.

Anyone try to install Optware on it and can confirm it's possible ?

I recently purchased a used NSLU2 with the intent of putting wview on it for
weather station support.

Upon installing the latest SlugOS per instructions, I cannot access the slug in
any way (telnet or via the web interface, nor any ping) once the installation is
complete and it reboots.  Reading around suggested I should install unslung OS
first and confirm the IP address is set to what I expect it to be.  Installing
unslung works fine.  I can install (including SSH) and configure as its
instructions suggest.  But then when installing SlugOS again, same response.  I
am not able to telnet or use the web interface (*.77 default).

Suggestions?

What instructions have you followed thus far?

Here's the definitive page (all others should be considered obsolete or
questionable at best):

http://www.nslu2-linux.org/wiki/SlugO/InstallandTurnupABasicSlugOSSystem

As noted by Patrick already, SlugOS has neither a telnet server nor a
web server installed -- SSH is the only way to communicate with SlugOS,
at least until you get some external storage configured and install
either a web server or a telnet server.

-Mike (mwester)



On 11/2/2012 11:33 AM, underscoretom wrote:
> I recently purchased a used NSLU2 with the intent of putting wview on it for
weather station support.
>
> Upon installing the latest SlugOS per instructions, I cannot access the slug
in any way (telnet or via the web interface, nor any ping) once the installation
is complete and it reboots.  Reading around suggested I should install unslung
OS first and confirm the IP address is set to what I expect it to be. 
Installing unslung works fine.  I can install (including SSH) and configure as
its instructions suggest.  But then when installing SlugOS again, same response.
I am not able to telnet or use the web interface (*.77 default).
>
> Suggestions?
>
>
>
> ------------------------------------
>
> Yahoo! Groups Links
>
>
>
>
>

I couldn't ping it, no.

As it turned out from googling I found a note that even if you use a static IP,
it should be in the DHCP range.  Once I did that, I was able to access things as
expected.

Thanks.

--- In nslu2-linux@yahoogroups.com, Patrick Mcgillan <patrick.mcgillan@...>
wrote:
>
> Can you ping it? Standard dos ping program should get answers which
> verifies not only that is alive, but you have the correct address. SSH is
> the only way as it doesn't have a telnet program. Go download Putty.exe,
> its free and works good.
>
> I just upgraded mine to Slug OS BE 3.15. Works great! By the way, there is
> no web server loaded. I installed lighttpd.
>
> Patrick
>
>
> On Fri, Nov 2, 2012 at 11:33 AM, underscoretom <underscore05@...>wrote:
>
> > **
> >
> >
> > I recently purchased a used NSLU2 with the intent of putting wview on it
> > for weather station support.
> >
> > Upon installing the latest SlugOS per instructions, I cannot access the
> > slug in any way (telnet or via the web interface, nor any ping) once the
> > installation is complete and it reboots. Reading around suggested I should
> > install unslung OS first and confirm the IP address is set to what I expect
> > it to be. Installing unslung works fine. I can install (including SSH) and
> > configure as its instructions suggest. But then when installing SlugOS
> > again, same response. I am not able to telnet or use the web interface
> > (*.77 default).
> >
> > Suggestions?
> >
> >
> >
>

THIS is or react Internet Link, for SlugOS.
Earlier link had a typo.

http://www.nslu2-linux.org/wiki/SlugOS/InstallandTurnupABasicSlugOSSystem


--- In nslu2-linux@yahoogroups.com, "Mike Westerhof (mwester)" <mwester@...>
wrote:
>
> What instructions have you followed thus far?
>
> Here's the definitive page (all others should be considered obsolete or
> questionable at best):
>
> http://www.nslu2-linux.org/wiki/SlugO/InstallandTurnupABasicSlugOSSystem
>
> As noted by Patrick already, SlugOS has neither a telnet server nor a
> web server installed -- SSH is the only way to communicate with SlugOS,
> at least until you get some external storage configured and install
> either a web server or a telnet server.
>
> -Mike (mwester)
>
>
>
> On 11/2/2012 11:33 AM, underscoretom wrote:
> > I recently purchased a used NSLU2 with the intent of putting wview on it for
weather station support.
> >
> > Upon installing the latest SlugOS per instructions, I cannot access the slug
in any way (telnet or via the web interface, nor any ping) once the installation
is complete and it reboots.  Reading around suggested I should install unslung
OS first and confirm the IP address is set to what I expect it to be. 
Installing unslung works fine.  I can install (including SSH) and configure as
its instructions suggest.  But then when installing SlugOS again, same response.
I am not able to telnet or use the web interface (*.77 default).
> >
> > Suggestions?
> >
> >
> >
> > ------------------------------------
> >
> > Yahoo! Groups Links
> >
> >
> >
> >
> >
>

You might try the optware feeds.

The instructions on the bottom of the installation page tell you how to
enable the optware feeds so that you can use "ipkg" to install from
optware (and "opkg" will continue to fetch the native SlugOS feed packages).

-Mike (mwester)

On 11/5/2012 8:53 AM, Patrick Mcgillan wrote:
>
>
> Its up and running fine, but I sure miss mc. Any quick clues on
> installing midnight commander. Maybe I missed something.
>
> opkg install mc - comes back and says can't find package.
>
> Patrick
>
>
>
>

package: syno-e500 aria2 1.14.1

when I try to enable json rpc through cli... a error occured

    --unrecognized+option+'--enable-rpc

any idea?

Hi Paulo,
I also was in this situation but for ddwrt.
I successfully compiled the version 2.73 for ddwrt simply by changing
the version in the makefile under optware/make/transmission.mk. I
changed the line TRANSMISSION_VERSION=2.73

I then recompiled the package with make transmission-ipk.

Attached to this message, I provide a compiled version of transmission 2.73.

Regards,


Le 19. 11. 12 23:24, Paulo Oliveira a écrit :
>
> Hello!
>
> Can someone help? Need to update transmission ipk for my iomega ix-200…
>
> Maintainer email is not available any more…
>
> Thanks
>
> Paulo Oliveira
>
> *De:*Paulo Oliveira [mailto:pjao.ct2jay@...]
> *Enviada**:*segunda-feira, 19 de Novembro de 2012 22:15
> *Para:* oleo@...
> *Assunto:* Plz update transmission for arm
>
> Hi there,
>
> Can you please update transmission package to thelatest version
> available (transmission-2.73
> <http://download-origin.transmissionbt.com/files/transmission-2.73.tar.bz2>)?
>
> The actual version as some annoying bugs on the web interface.
>
> Thanks for your suport!
>
> Chears
>
> Paulo Oliveira
>
>
--------------------------------------------------------------------------------
>
> http://ipkg.nslu2-linux.org/feeds/optware/cs08q1armel/cross/unstable/Packages
>
> Package: transmission
>
> Version: 2.61-1
>
> Depends: openssl, libcurl, libevent, zlib
>
> Section: net
>
> Architecture: arm
>
> Maintainer: oleo@... <mailto:oleo@...>
>
> MD5Sum: bae39b48501f0e06d3592266a93ba40a
>
> Size: 1475467
>
> Filename: transmission_2.61-1_arm.ipk
>
> Source:
> http://mirrors.m0k.org/transmission/files/transmission-2.61.tar.bz2
>
> Description: Lightweight BitTorrent client and daemon, with web
> interface bundled.
>
>

I updated the makefile.  Binaries should pop up soon in the feeds.

Regards,
Ovidiu Sas

On Mon, Nov 19, 2012 at 6:18 PM, nas <nas@...> wrote:
> Hi Paulo,
> I also was in this situation but for ddwrt.
> I successfully compiled the version 2.73 for ddwrt simply by changing
> the version in the makefile under optware/make/transmission.mk. I
> changed the line TRANSMISSION_VERSION=2.73
>
> I then recompiled the package with make transmission-ipk.
>
> Attached to this message, I provide a compiled version of transmission 2.73.
>
> Regards,
>
>
> Le 19. 11. 12 23:24, Paulo Oliveira a écrit :
>>
>> Hello!
>>
>> Can someone help? Need to update transmission ipk for my iomega ix-200…
>>
>> Maintainer email is not available any more…
>>
>> Thanks
>>
>> Paulo Oliveira
>>
>> *De:*Paulo Oliveira [mailto:pjao.ct2jay@...]
>> *Enviada**:*segunda-feira, 19 de Novembro de 2012 22:15
>> *Para:* oleo@...
>> *Assunto:* Plz update transmission for arm
>>
>> Hi there,
>>
>> Can you please update transmission package to thelatest version
>> available (transmission-2.73
>> <http://download-origin.transmissionbt.com/files/transmission-2.73.tar.bz2>)?
>>
>> The actual version as some annoying bugs on the web interface.
>>
>> Thanks for your suport!
>>
>> Chears
>>
>> Paulo Oliveira
>>
>>
--------------------------------------------------------------------------------
>>
>> http://ipkg.nslu2-linux.org/feeds/optware/cs08q1armel/cross/unstable/Packages
>>
>> Package: transmission
>>
>> Version: 2.61-1
>>
>> Depends: openssl, libcurl, libevent, zlib
>>
>> Section: net
>>
>> Architecture: arm
>>
>> Maintainer: oleo@... <mailto:oleo@...>
>>
>> MD5Sum: bae39b48501f0e06d3592266a93ba40a
>>
>> Size: 1475467
>>
>> Filename: transmission_2.61-1_arm.ipk
>>
>> Source:
>> http://mirrors.m0k.org/transmission/files/transmission-2.61.tar.bz2
>>
>> Description: Lightweight BitTorrent client and daemon, with web
>> interface bundled.

Hi all!

Thanks for yours fast reply!

Ovidiu as updated that makefile and is now avaiable for all!

Great job!
Paulo Oliveira

--- In nslu2-linux@yahoogroups.com, Ovidiu Sas <osas@...> wrote:
>
> I updated the makefile.  Binaries should pop up soon in the feeds.
>
> Regards,
> Ovidiu Sas
>
> On Mon, Nov 19, 2012 at 6:18 PM, nas <nas@...> wrote:
> > Hi Paulo,
> > I also was in this situation but for ddwrt.
> > I successfully compiled the version 2.73 for ddwrt simply by changing
> > the version in the makefile under optware/make/transmission.mk. I
> > changed the line TRANSMISSION_VERSION=2.73
> >
> > I then recompiled the package with make transmission-ipk.
> >
> > Attached to this message, I provide a compiled version of transmission 2.73.
> >
> > Regards,
> >
> >
> > Le 19. 11. 12 23:24, Paulo Oliveira a écrit :
> >>
> >> Hello!
> >>
> >> Can someone help? Need to update transmission ipk for my iomega ix-200…
> >>
> >> Maintainer email is not available any more…
> >>
> >> Thanks
> >>
> >> Paulo Oliveira
> >>
> >> *De:*Paulo Oliveira [mailto:pjao.ct2jay@...]
> >> *Enviada**:*segunda-feira, 19 de Novembro de 2012 22:15
> >> *Para:* oleo@...
> >> *Assunto:* Plz update transmission for arm
> >>
> >> Hi there,
> >>
> >> Can you please update transmission package to thelatest version
> >> available (transmission-2.73
> >>
<http://download-origin.transmissionbt.com/files/transmission-2.73.tar.bz2>)?
> >>
> >> The actual version as some annoying bugs on the web interface.
> >>
> >> Thanks for your suport!
> >>
> >> Chears
> >>
> >> Paulo Oliveira
> >>
> >>
--------------------------------------------------------------------------------
> >>
> >>
http://ipkg.nslu2-linux.org/feeds/optware/cs08q1armel/cross/unstable/Packages
> >>
> >> Package: transmission
> >>
> >> Version: 2.61-1
> >>
> >> Depends: openssl, libcurl, libevent, zlib
> >>
> >> Section: net
> >>
> >> Architecture: arm
> >>
> >> Maintainer: oleo@... <mailto:oleo@...>
> >>
> >> MD5Sum: bae39b48501f0e06d3592266a93ba40a
> >>
> >> Size: 1475467
> >>
> >> Filename: transmission_2.61-1_arm.ipk
> >>
> >> Source:
> >> http://mirrors.m0k.org/transmission/files/transmission-2.61.tar.bz2
> >>
> >> Description: Lightweight BitTorrent client and daemon, with web
> >> interface bundled.
>

--- In nslu2-linux@yahoogroups.com, Andreas Reitz <andyr@...> wrote:
> Hi,
>
> since there's a 32bit Version of HipHop (Facebooks PHP->C++ Compiler)
> available, i would like to know if someone tried to compile it on the
> slug (or another arm device like dockstar,...). I'm playing a lot with
> php and it seems like a good possibility to reduce system load.
>
> Greets

Hi Andreas,

Have you got any informations?
I would like to install it on Broadcom MIPS

Hi,
I've installed apcupsd package on an armel cpu (QNAP TS-412) but seems that
there is an incongruence, the version of the package doesn't correspond to the
version of the installed binary.
I think that the output of my shell is self explaining (at the end of the
message)
Moreover, the binary doesn't work at all and exit with an "abort" (the second
attachment). There is some way to rebuild the package and correct my problems?
Can be update to the last release (3.14.10)?
Thanks a lot!
Francesco


PS shell output:
# apcupsd --version
apcupsd 3.10.15 (04 August 2004) debian
# ipkg info apcupsd
Package: apcupsd
Version: 3.14.8-1
Status: install user installed
Section: sysadmin
Architecture: arm
maintainer: NSLU2 Linux <nslu2-linux@yahoogroups.com>
MD5Sum: 55e9c73eb19d49c53cf7997c7e0783c6
Size: 212115
Filename: apcupsd_3.14.8-1_arm.ipk
Source:
http://downloads.sourceforge.net/sourceforge/apcupsd/apcupsd-3.14.8.tar.gz
Description: A daemon for controlling APC UPSes

Successfully terminated.



PS2 exiting message:
# apcupsd -b
*** glibc detected *** apcupsd: double free or corruption (top): 0x000359e8 ***
======= Backtrace: =========
/lib/libc.so.6[0x400b4000]
/lib/libc.so.6[0x400b50ac]
/lib/libc.so.6(cfree+0x164)[0x400b5758]
/lib/libc.so.6(fclose+0x36c)[0x400a178c]
apcupsd[0x142b8]
apcupsd(vfprintf+0x37e8)[0xd108]
apcupsd(vfprintf+0x77c)[0xa09c]
/lib/libc.so.6(__libc_start_main+0x1bc)[0x4005a924]
apcupsd(fputs+0x34)[0x9a08]
======= Memory map: ========
00008000-00022000 r-xp 00000000 01:00 330        /sbin/apcupsd
0002a000-0002b000 rwxp 0001a000 01:00 330        /sbin/apcupsd
0002b000-00056000 rwxp 00000000 00:00 0          [heap]
40000000-4001d000 r-xp 00000000 01:00 88         /lib/ld-2.5.so
4001d000-4001e000 rwxp 00000000 00:00 0
40024000-40026000 rwxp 0001c000 01:00 88         /lib/ld-2.5.so
40026000-4003b000 r-xp 00000000 01:00 82         /lib/libpthread-2.5.so
4003b000-40042000 ---p 00015000 01:00 82         /lib/libpthread-2.5.so
40042000-40043000 r-xp 00014000 01:00 82         /lib/libpthread-2.5.so
40043000-40044000 rwxp 00015000 01:00 82         /lib/libpthread-2.5.so
40044000-40046000 rwxp 00000000 00:00 0
40046000-4016d000 r-xp 00000000 01:00 107        /lib/libc-2.5.so
4016d000-40174000 ---p 00127000 01:00 107        /lib/libc-2.5.so
40174000-40175000 r-xp 00126000 01:00 107        /lib/libc-2.5.so
40175000-40177000 rwxp 00127000 01:00 107        /lib/libc-2.5.so
40177000-4017b000 rwxp 00000000 00:00 0
bee7e000-bee93000 rw-p 00000000 00:00 0          [stack]
Aborted

As you see in your output, the binary is provided by debian and it is
the stock installed version in /sbin.
You will need to look under /opt (using full path) to invoke the ipkg
installed apcupsd.

Regards,
Ovidiu Sas

On Mon, Dec 10, 2012 at 2:57 PM, onlyfrancy86 <onlyfrancy86@...> wrote:
>
>
>
> Hi,
> I've installed apcupsd package on an armel cpu (QNAP TS-412) but seems that
there is an incongruence, the version of the package doesn't correspond to the
version of the installed binary.
> I think that the output of my shell is self explaining (at the end of the
message)
> Moreover, the binary doesn't work at all and exit with an "abort" (the second
attachment). There is some way to rebuild the package and correct my problems?
> Can be update to the last release (3.14.10)?
> Thanks a lot!
> Francesco
>
> PS shell output:
> # apcupsd --version
> apcupsd 3.10.15 (04 August 2004) debian
> # ipkg info apcupsd
> Package: apcupsd
> Version: 3.14.8-1
> Status: install user installed
> Section: sysadmin
> Architecture: arm
> maintainer: NSLU2 Linux <nslu2-linux@yahoogroups.com>
> MD5Sum: 55e9c73eb19d49c53cf7997c7e0783c6
> Size: 212115
> Filename: apcupsd_3.14.8-1_arm.ipk
> Source:
http://downloads.sourceforge.net/sourceforge/apcupsd/apcupsd-3.14.8.tar.gz
> Description: A daemon for controlling APC UPSes
>
> Successfully terminated.
>
> PS2 exiting message:
> # apcupsd -b
> *** glibc detected *** apcupsd: double free or corruption (top): 0x000359e8
***
> ======= Backtrace: =========
> /lib/libc.so.6[0x400b4000]
> /lib/libc.so.6[0x400b50ac]
> /lib/libc.so.6(cfree+0x164)[0x400b5758]
> /lib/libc.so.6(fclose+0x36c)[0x400a178c]
> apcupsd[0x142b8]
> apcupsd(vfprintf+0x37e8)[0xd108]
> apcupsd(vfprintf+0x77c)[0xa09c]
> /lib/libc.so.6(__libc_start_main+0x1bc)[0x4005a924]
> apcupsd(fputs+0x34)[0x9a08]
> ======= Memory map: ========
> 00008000-00022000 r-xp 00000000 01:00 330 /sbin/apcupsd
> 0002a000-0002b000 rwxp 0001a000 01:00 330 /sbin/apcupsd
> 0002b000-00056000 rwxp 00000000 00:00 0 [heap]
> 40000000-4001d000 r-xp 00000000 01:00 88 /lib/ld-2.5.so
> 4001d000-4001e000 rwxp 00000000 00:00 0
> 40024000-40026000 rwxp 0001c000 01:00 88 /lib/ld-2.5.so
> 40026000-4003b000 r-xp 00000000 01:00 82 /lib/libpthread-2.5.so
> 4003b000-40042000 ---p 00015000 01:00 82 /lib/libpthread-2.5.so
> 40042000-40043000 r-xp 00014000 01:00 82 /lib/libpthread-2.5.so
> 40043000-40044000 rwxp 00015000 01:00 82 /lib/libpthread-2.5.so
> 40044000-40046000 rwxp 00000000 00:00 0
> 40046000-4016d000 r-xp 00000000 01:00 107 /lib/libc-2.5.so
> 4016d000-40174000 ---p 00127000 01:00 107 /lib/libc-2.5.so
> 40174000-40175000 r-xp 00126000 01:00 107 /lib/libc-2.5.so
> 40175000-40177000 rwxp 00127000 01:00 107 /lib/libc-2.5.so
> 40177000-4017b000 rwxp 00000000 00:00 0
> bee7e000-bee93000 rw-p 00000000 00:00 0 [stack]
> Aborted
>

Thanks a lot, it helps!
The problem was my PATH variable that export /opt/sbin after /sbin/.

Francesco


Il 10/12/2012 21:08, Ovidiu Sas ha scritto:
> As you see in your output, the binary is provided by debian and it is
> the stock installed version in /sbin.
> You will need to look under /opt (using full path) to invoke the ipkg
> installed apcupsd.
>
> Regards,
> Ovidiu Sas
>
> On Mon, Dec 10, 2012 at 2:57 PM, onlyfrancy86 <onlyfrancy86@...
> <mailto:onlyfrancy86%40yahoo.it>> wrote:
>  >
>  >
>  >
>  > Hi,
>  > I've installed apcupsd package on an armel cpu (QNAP TS-412) but
> seems that there is an incongruence, the version of the package doesn't
> correspond to the version of the installed binary.
>  > I think that the output of my shell is self explaining (at the end of
> the message)
>  > Moreover, the binary doesn't work at all and exit with an "abort"
> (the second attachment). There is some way to rebuild the package and
> correct my problems?
>  > Can be update to the last release (3.14.10)?
>  > Thanks a lot!
>  > Francesco
>  >
>  > PS shell output:
>  > # apcupsd --version
>  > apcupsd 3.10.15 (04 August 2004) debian
>  > # ipkg info apcupsd
>  > Package: apcupsd
>  > Version: 3.14.8-1
>  > Status: install user installed
>  > Section: sysadmin
>  > Architecture: arm
>  > maintainer: NSLU2 Linux <nslu2-linux@yahoogroups.com
> <mailto:nslu2-linux%40yahoogroups.com>>
>  > MD5Sum: 55e9c73eb19d49c53cf7997c7e0783c6
>  > Size: 212115
>  > Filename: apcupsd_3.14.8-1_arm.ipk
>  > Source:
> http://downloads.sourceforge.net/sourceforge/apcupsd/apcupsd-3.14.8.tar.gz
>  > Description: A daemon for controlling APC UPSes
>  >
>  > Successfully terminated.
>  >
>  > PS2 exiting message:
>  > # apcupsd -b
>  > *** glibc detected *** apcupsd: double free or corruption (top):
> 0x000359e8 ***
>  > ======= Backtrace: =========
>  > /lib/libc.so.6[0x400b4000]
>  > /lib/libc.so.6[0x400b50ac]
>  > /lib/libc.so.6(cfree+0x164)[0x400b5758]
>  > /lib/libc.so.6(fclose+0x36c)[0x400a178c]
>  > apcupsd[0x142b8]
>  > apcupsd(vfprintf+0x37e8)[0xd108]
>  > apcupsd(vfprintf+0x77c)[0xa09c]
>  > /lib/libc.so.6(__libc_start_main+0x1bc)[0x4005a924]
>  > apcupsd(fputs+0x34)[0x9a08]
>  > ======= Memory map: ========
>  > 00008000-00022000 r-xp 00000000 01:00 330 /sbin/apcupsd
>  > 0002a000-0002b000 rwxp 0001a000 01:00 330 /sbin/apcupsd
>  > 0002b000-00056000 rwxp 00000000 00:00 0 [heap]
>  > 40000000-4001d000 r-xp 00000000 01:00 88 /lib/ld-2.5.so
>  > 4001d000-4001e000 rwxp 00000000 00:00 0
>  > 40024000-40026000 rwxp 0001c000 01:00 88 /lib/ld-2.5.so
>  > 40026000-4003b000 r-xp 00000000 01:00 82 /lib/libpthread-2.5.so
>  > 4003b000-40042000 ---p 00015000 01:00 82 /lib/libpthread-2.5.so
>  > 40042000-40043000 r-xp 00014000 01:00 82 /lib/libpthread-2.5.so
>  > 40043000-40044000 rwxp 00015000 01:00 82 /lib/libpthread-2.5.so
>  > 40044000-40046000 rwxp 00000000 00:00 0
>  > 40046000-4016d000 r-xp 00000000 01:00 107 /lib/libc-2.5.so
>  > 4016d000-40174000 ---p 00127000 01:00 107 /lib/libc-2.5.so
>  > 40174000-40175000 r-xp 00126000 01:00 107 /lib/libc-2.5.so
>  > 40175000-40177000 rwxp 00127000 01:00 107 /lib/libc-2.5.so
>  > 40177000-4017b000 rwxp 00000000 00:00 0
>  > bee7e000-bee93000 rw-p 00000000 00:00 0 [stack]
>  > Aborted
>  >
>
>

Better ARM support has been added to Linux 3.7. I see that there has been some
discussion about the IXP420:

http://linux-kernel.2935.n7.nabble.com/Re-PULL-REQ-IXP4xx-changes-for-Linux-3-7-\
td368783.html

Does anyone have more information about using the 3.7 kernel with the NSLU2?

http://www.slug-firmware.net/d-click.php?p=download%2Fdebian%2Fnslu2&f=debian-ar\
mel-5.0.9.zip&l=d-license.txt&k=28b96fef901eabfbf1562aaa880cf19d


hope helps somebody


best regards

Pio

http://www.slug-firmware.net/d-click.php?p=download%2Fdebian%2Fnslu2&f=debian-ar\
mel-5.0.9.zip&l=d-license.txt&k=28b96fef901eabfbf1562aaa880cf19d


best regards


Pio


--- In nslu2-linux@yahoogroups.com, Carlos Garces <carlos.garces@...> wrote:
>
> Hi!
>
>
> The Debian installer is no longer supported on the NSLU2, but ¿what
> happened with the old versions?
>
> I'm looking the installer for Debian 5.¿Any one have a copy of 5.0.4 or
> 5.0.9 firmware?
>
> Un saludo
> Carlos Garcés
>

I want to report a bug and hopefully it will get resolved shortly.The problem
was when I tried to install asterisk18 (1.8.19.1-1) package from Optware for my
ASUS RT-N16 router with DD-WRT firmware v.24 -sp2 (14929 mega build), it failed.
A message was displayed saying that the asterisk18 is conflicting with
asterisk14. The package itself is located in
http://ipkg.nslu2-linux.org/feeds/optware/ddwrt/cross/stable/asterisk_1.8.19.1-1\
_mipsel.ipk. Thanks.

Abe

 

I want to report a bug and hopefully it will get resolved shortly.The problem was when I tried to install asterisk18 (1.8.19.1-1) package from Optware for my ASUS RT-N16 router with DD-WRT firmware v.24 -sp2 (14929 mega build), it failed. A message was displayed saying that the asterisk18 is conflicting with asterisk14. The package itself is located in http://ipkg.nslu2-linux.org/feeds/optware/ddwrt/cross/stable/asterisk_1.8.19.1-1_mipsel.ipk. Thanks.

Abe

-- Comdif Telecom,
Landline +33469665501
Mobile +33689816533

This is not a bug. There are several asterisk packages:
  - asterisk12 - asterisk 1.2.x
  - asterisk14 - asterisk 1.4.x
  - asterisk16 - asterisk 1.6.x
  - asterisk18 - asterisk 1.8.x
  - asterisk10 - asterisk 10.x

Pick the one that you are familiar with it and install it.  Do not
install two of them at the same time.
We should remove asterisk12, asterisk14 and asterisk16 as those are no
longer supported.

Regards,
Ovidiu Sas

On Mon, Jan 7, 2013 at 1:28 PM, A <goody1240@...> wrote:
>
>
>
> I want to report a bug and hopefully it will get resolved shortly.The problem
was when I tried to install asterisk18 (1.8.19.1-1) package from Optware for my
ASUS RT-N16 router with DD-WRT firmware v.24 -sp2 (14929 mega build), it failed.
A message was displayed saying that the asterisk18 is conflicting with
asterisk14. The package itself is located in
http://ipkg.nslu2-linux.org/feeds/optware/ddwrt/cross/stable/asterisk_1.8.19.1-1\
_mipsel.ipk. Thanks.
>
> Abe

Hello,

I am new here. the last 4 weeks I searched several forums found by google, but
didn't find a final solution, so now I try to ask actively ....

But first something about me/my Equipment:
About 3 years ago got my first NSLU2 - meanwhile I have 3 of them, all running
under uNSLUng-6.10-beta.
First one in the basement, with 2 HDDs.
Second one below the roof, 1 HDD.
Third in my working room, with a 2-GB-Stick on Port 2 and a Samsung
ML-1520-Laser directly connected to USB1.

Now here I come to the problem:

I started with a freshly flashed NSLU2, connected the Stick to USB2, moved OS to
there, installed cups and customized it like described here:
http://www.nslu2-linux.org/wiki/HowTo/AddPrinter

Cups is running and accessably via browser from my net, but:

At my NSLU2 just 3 of the green LEDs burn, the one for USB1 is off.

The box knows printer is there::

"# cat /proc/bus/usb/devices
T: Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 0.00
S: Product=USB OHCI Root Hub
S: SerialNumber=c3880000
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 3
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 0.00
S: Product=USB OHCI Root Hub
S: SerialNumber=c387a000
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=16 #Cfgs= 1
P: Vendor=04e8 ProdID=3256 Rev= 1.00
S: Manufacturer=Samsung Electronics Co., Ltd.
S: Product=Samsung ML-1520 Series
S: SerialNumber=2X21BRJY109519..
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=07(print) Sub=01 Prot=02 Driver=(none)
E: Ad=03(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 5
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.04
S: Manufacturer=Linux 2.4.22-xfs ehci_hcd
S: Product=NEC Corporation USB 2.0
S: SerialNumber=00:01.2
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=256ms
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=0781 ProdID=5204 Rev= 0.10
S: Manufacturer=SanDisk Corporation
S: Product=Cruzer Crossfire
S: SerialNumber=200426056216573368BC
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=200mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=125us"

Or maybe not ??:
"# lsmod
Module Size Used by Tainted: P
ufsd 164872 0 (unused)
x1226-rtc 3664 0
rbuttons 1304 0 (unused)
pbuttons 800 0 (unused)
ixp425_eth 17116 0 (unused)
ixp400 608216 0 [ixp425_eth]"

I recreated both lp0/lp1 and provided all access rights (777):
"# ls /dev/lp* -l
crwxrwxrwx 1 root root 180, 0 Dec 28 01:17 /dev/lp0
crw-rw-rw- 1 root root 180, 0 Dec 22 22:44 /dev/lp1
crw-r--r-- 1 root root 180, 2 Jan 1 1970 /dev/lp2
crw-r--r-- 1 root root 180, 3 Jan 1 1970 /dev/lp3"

Nevertheless Cups-Page tells me:
"Samsung_ML_1520 Ich stehe im Arbeitszimmer Local Raw Printer Angehalten -
"Gerätedatei „/dev/lp0" konnte nicht geöffnet werden – No such device""

I at first entered my Samsung ML 1520 in the /opt/etc/cups/cupsd.conf, but when
this didn't work I added a printer via the cups-Site - but both do not work:

"# lpstat -t
scheduler is running
system default destination: Samsung_ML_1520
device for ML-1520: http://az_server:631/lp0
device for Samsung_ML_1520: parallel:/dev/lp0
ML-1520 accepting requests since Sat Jan 5 00:04:13 2013
Samsung_ML_1520 accepting requests since Mon Dec 10 22:10:49 2012
printer ML-1520 disabled since Sat Jan 5 00:04:13 2013 -
Zieldrucker existiert nicht!
printer Samsung_ML_1520 disabled since Mon Dec 10 22:10:49 2012 -
Gerätedatei â/dev/lp0â konnte nicht geöffnet werden â No such device
ML-1520-2 admin 1024 Sat Jan 5 00:03:25 2013"

"# lpc status
ML-1520:
printer is on device 'http' speed -1
queuing is enabled
printing is disabled
1 entries
daemon present
Samsung_ML_1520:
printer is on device 'parallel' speed -1
queuing is enabled
printing is disabled
no entries
daemon present"

What might be a basic problem:
Cups did not install a  "printer.o"

Here is my installes list:
"# ipkg list_installed
adduser - 1.10.3-1 - a multi-call binary for login and user account
administration
coreutils - 8.4-1 - Bunch of heavyweight *nix core utilities
cups - 1.4.6-1 - Common Unix Printing System
cups-doc - 1.4.6-1 - Common Unix Printing System documentation.
cups-driver-gutenprint - 5.2.6-1 - CUPS driver from Gutenprint.
cups-locale-de - 1.4.6-1 - CUPS documentation, template and locale files for de
cups-pdf - 2.5.1-1 - CUPS-PDF provides a PDF Writer backend to CUPS. This can be
used as a virtual printer in a paperless network.
cyrus-sasl-libs - 2.1.23-2 - Provides client or server side authentication (see
RFC 2222).
dbus - 1.2.16-1 - D-Bus is a message bus system, a simple way for applications
to talk to one another.
dbus-glib - 0.82-1 - D-Bus Glib bindings
e2fslibs - 1.41.14-1 - Ext2 Filesystem Libraries
expat - 2.0.1-1 - XML Parser library
fontconfig - 2.8.0-0 - Font configuration library
freetype - 2.3.6-1 - Free truetype library
gconv-modules - 2.2.5-7 - Provides gconv modules missing from the firmware.
These are used by glibc iconv() implementation.
gdbm - 1.8.3-4 - GNU dbm is a set of database routines that use extensible
hashing. It works similar to the standard UNIX dbm routines.
ghostscript - 8.71-2 - An interpreter for the PostScript (TM) language
glib - 2.20.4-1 - The GLib library of C routines.
gutenprint - 5.2.6-1 - Gutenprint.
ipkg - 0.99.163-r6 - Itsy Package Manager
kernel - 2.4.22.l2.3r63-r21 - Vendor-compatible Linux kernel for the Linksys
NSLU2 device
kernel-2.4.22-xfs - 2.4.22.l2.3r63-r21 - Vendor-compatible Linux kernel for the
Linksys NSLU2 device
kernel-image-2.4.22-xfs - 2.4.22.l2.3r63-r21 - Vendor-compatible Linux kernel
for the Linksys NSLU2 device
kernel-module-netconsole - 2.4.22.l2.3r63-r21 - netconsole kernel module; kernel
network console implementation
libc6-unslung - 2.2.5-r13 - GNU C Library
libdb - 4.2.52-3 - Berkeley DB Libraries
libgcc - 3.4.4-r7 - The GNU cc and gcc C compilers.
libijs - 0.35-1 - IJS raster image transport protocol
libipkg - 0.99.163-r6 - Itsy Package Manager Library
libjpeg - 6b-3 - collection of jpeg tools
libpng - 1.2.44-1 - Portable Network Graphics Libraries
libstdc++ - 5.0.7-6 - Standard C++ library, needed for dynamically linked C++
programs
libtiff - 3.9.5-1 - Tag Image File Format Libraries
mc - 4.7.5.5-1 - Midnight Commander File Manager
ncurses - 5.7-3 - NCurses libraries
nslu2-linksys-libs - 2.3r63-r3 - Linksys NSLU2 Stock Firmware Libraries.
openldap-libs - 2.3.43-2 - Open Lightweight Directory Access Protocol
openssh - 5.9p1-1 - a FREE version of the SSH protocol suite of network
connectivity tools.
openssl - 0.9.7m-6 - Openssl provides the ssl implementation in libraries
libcrypto and libssl, and is needed by many other applications and librari
psmisc - 22.11-1 - A set of some small useful utilities that use the proc
filesystem.
readline - 6.1-2 - The GNU Readline library provides a set of functions for use
by applications that allow users to edit command lines as they are
slang - 2.2.3-2 - S-Lang is a multi-platform library designed to allow a
developer to create robust multi-platform software.
slingbox - 1.3.1-r2 - SlingBox is a minimal version of BusyBox with just enough
functionality to enable ipkg to run on an Unslung NSLU2 device.
splix - 2.0.0-1 - Splix is a driver for printers that speak SPL (Samsung Printer
Language). This includes printers made by Samsung, Dell, and Xer
unslung-rootfs - 2.3r63-r22 - Version 2.3r63-r22 of package unslung-rootfs
update-modules - 1.0-r6 - Script to manage module configuration files
update-rc.d - 0.7-r1 - Manage symlinks in /etc/rcN.d
zlib - 1.2.5-1 - zlib is a library implementing the 'deflate' compression
system."

Thats all - no idea how I get this to work. :-(

Before I had my printer connected by a lonshine usb server - but this wasn't
reliable. Thought switching to cups was a good idea agains frequently asked
question of my wife: "Is it printing?" ...

Do you think it might be enough to add "printer.o" in /opt/lib/modules/ ? And -
where do I get it from ?

PLEASE HELP ME !!!.

Best regards from Mainz (Germany)
Christian