Hi, I'm getting the scanning has failed message each time I try and scan a page. This happens whether or not open book is loaded or unloaded. Recently I didn't...
John Gassman
johngassman@...
Jun 6, 2007 1:32 pm
10973
If the USB cable isn't permanently attached to the back of the scanner you can unplug it there and get the same effect. ... From: John Gassman To:...
Hi John, You wrote: I'm getting the scanning has failed message each time I try and scan a page. This happens whether or not open book is loaded or unloaded. ...
Tom Lange
trlange@...
Jun 6, 2007 2:30 pm
10975
Hi John, It would seem that HP does have a path to the 5200C drivers and support information. Here's how you get there. From the main HP page at ...
Tom Lange
trlange@...
Jun 6, 2007 3:53 pm
10976
one thing. unless you have the scanner on a power strip it is on all the time. you can not turn it off. do you hear the scanner when you turn it on? if not...
This may seem simplistic, but are you using the automatic orientation when scanning? I find that I have problems when trying to outthink Openbook. Sunny Day ...
Maria Campbell
lucky1inct@...
Jun 6, 2007 4:15 pm
10978
Hi John and list! Check to see if Windows recognises your scanner. It will be listed in the scanners and cameras section of control panel. Go into properties...
Hi, Windows does recognize my scanner. I did test it successfully. I found the driver download page but when I tried to download and install the driver I got...
John Gassman
johngassman@...
Jun 7, 2007 3:41 am
10980
as i said yesterday if you have the windows xp cd the hp 5200 drivers are already on the disk and can be installed from there. you do not have to go to there...
if the scanner was detected and the test passed than you probably don't have to reinstall the driver. there is something else wrong. does the scanner make a...
Unfortunately, XP came loaded onthis computer and I don't believe I have the disk. ... John Gassman mailto:johngassman@... Recognition Of The...
John Gassman
johngassman@...
Jun 7, 2007 1:02 pm
10983
I'll give it a try. Thanks! ... John Gassman mailto:johngassman@... Recognition Of The Problem is 51% Of The Solution...
John Gassman
johngassman@...
Jun 7, 2007 1:02 pm
10984
i would still look in openboook scanner first to make sure it has not change to no scanner. openbook will do this if it was loaded with the scanner off. it...
Press Alt + n to get a menu that will allow you to use the ActiveX. ... Hi, Windows does recognize my scanner. I did test it successfully. I found the driver...
Sid Ordway
docsgo@...
Jun 8, 2007 6:31 am
10986
If you need a new scanner, try to find the Epson 1660. I don't think they make them any more, but as you know, I've had one for about 3 years and have had no...
Larry Gassman
lgsinger@...
Jun 8, 2007 2:30 pm
10987
make sure you can get vista drivers for it first even if you do not have vista right now. xp is only going to be supported until 2009 and if you can not get...
Hi, alt plus n does nothing. I hope I'm not interpreting your dirrections incorrectly. I'm using IE 7. John ... John Gassman mailto:johngassman@... ...
John Gassman
johngassman@...
Jun 10, 2007 12:54 pm
10989
Are you doing Alt+N from inside Open Book? I would assume you are....
Larry Gassman
lgsinger@...
Jun 10, 2007 3:13 pm
10990
No, I used alt plus n from inside internet explorer 7. But I don't get anything from within open book when I pres that key combination either. ... John...
John Gassman
johngassman@...
Jun 10, 2007 3:25 pm
10991
Hello, I downloaded some pdf books. When I opened I read they were digital copies. Is there any way to read these books? I only can read some lines added by...
Tataindi
tataindi@...
Jun 12, 2007 1:49 pm
10992
Make sure OpenBook is running and then open your pdf file go to file and choose print then choose Freedom Printer and click OK. This should scan it to...
i don't know about openbook 6 but with openbook 7 and adobe 7 this will not work. it will say there is no application associated for this action. you have to...
Hello, I opened the pdf and openbook. I pressed alt and went down with the arrow to print. It says print inactive. What does it mean? What can I do to active...
Tataindi
tataindi@...
Jun 12, 2007 5:00 pm
10995
if you are useing adobe 7 this will not work. close openbook. load the file into adobe, open the file pull down and print. use the up or down arrow keys to...
I have OpenBook 7.02 and Adobe Reader 7 and if openbook is not running and I click on the freedom printer OpenBook opens and my scanner starts. But if OpenBook...
Hello, I did as you said, and it just finished. Would you please tell me what should I do now? I imagine I have to save it. What is the best to save it? Can...
Tataindi
tataindi@...
Jun 12, 2007 9:22 pm
10998
go to the files pull down in openbook and use save as. tthen tab to the type of file you want to save it as. likr a text file, word star, word perfect. etc....
Hello, I have a problem. While I was trying to save and before I saved, openbook disappeared. When I opened again, I couldn't find the scanned file anymore. ...
Tataindi
tataindi@...
Jun 12, 2007 11:07 pm
11000
it did not erace youroriginal pdf file. you could just do the process again by reloading it into adobe and re printing it with the freedom import printer. you...
With regard to the book you have been working on, have you been able to print it from Adobe to the freedom import printer and get access to the material? The...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
