I have problem with Blaupunkt Ontario DJ30 BP0320.MCU is from "ST" M990G0005C eeprom is 24c08 smd.I need good dump or help,radio is dead ,on display no any...
Hello, Does anybody have a list of what each elaboration codes means (for VW)? And where I can download and updated list of VAG DTCs (2000 or 2001)? Thanks Eze...
Hello, Is anybody have information about OBD-1 Volkswagen like address of variables, electrical information and how to talk to the system. We want to make a...
vincent@...
Mar 6, 2003 7:54 pm
1590
I have a Jeep Liberty 2002 and built Jeff's interface to read the OBDII interface. I have linux 6.0 loaded on an old laptop and tried using the freediag...
freediag should have not had a problem talking to jeff's interface (unless you have a h/w problem with the interface) (1) load up the latest verison of...
Do you have any info about flashing ECUs?... commands,dataformats... I have info about some commands you ask, but I need info about how to read/write memory....
Hello, which tool you use to flash ECU memory? Do you have any info about flashing VW memory? I need it! I want to exchange any info with you! Best Wishes, ...
Hello, Could you tell me how to communicate with ECU via OBDII protocol? I need only basis info. How to begin communication, is any background communication,...
Hi there, I'm new at this OBD things... Can anyone help me and tell me what hardware/software do I need to connect my car to my laptop? Has anyone tried it and...
Hi everybody, Do anybody have knowledge of the original renault diagnostic equipment. It is a laptop with an interface module and some special cables. I want...
I have ddt software and schematic of working interface ! Email me privatly if you are interested ! INFO <info@...> wrote: Hi everybody, Do anybody have...
Does anyone know where I can get the male connectors that connect to the 2x2 1992 Corrado G60 diag terminals? I would like to make my own cable. I don't...
I am only able to connect to my transmission computer, on my 1992 G60, using a homemade adapter using Jeff's design, with VAG-COM. I was able to connect to my...
The G60 still works with blink codes....... SFC ... From: Travis To: opendiag@yahoogroups.com Sent: Monday, March 10, 2003 7:40 AM Subject: [opendiag] Can't...
Hi, @Conner, I think the flasher in question is the ARP for ECMS, if you are talking about another one please let us know. "If you want to reprogram your car i...
Hello, what do you mean mit "ARP for ECMS"? What tool is that? I am not aware of that. ... From: lellobello2 [mailto:lellobello2@...] Sent: Tuesday, March...
Hi, This is a cut from the PDF file of the APR EMCS : "The EMCS Home Flash utility will allow you to upgrade your APR EMCS equipped engine control unit to the...
Hi all :) After i successfully read my old car Ecu's (BMW 530d - DDE 4) .... and waiting for infos regarding my new car (BMW 320d - EDC 16) i'm playing with my...
Hi, ... Little bit late, but yes. I wrote my own disassembler. Do you have any information about these MCUs ? Registers, etc. Is it possible to run some ...
I've been building Andy Whittaker's OBDII interface, when I tried using VAG-COM to test the COM1 and interface it says that COM1 is OK but could not find the...
Hi, Yhe OBD interface is nothing more than a level converter, it receives data from PC from the line RX (+ or - 10 Volt) and converts it to (0 or +12...
I'm looking for any infos about Honda ECUs. Especially for '90 Civic - with D13B2 engine - ECU and how can I setup/fine-tune/diagnose it. Thanks in advance ! ...
... Hello, You are sending TesterPresent Message in KWP2000 - ShortFormat and InitSequence is [ probably] not accepted. Let's explain: For KWP2K You should use...
Thanks for your help, Does this echo suppose to work when the interface is NOT connected to the car, because I tried to type on hyperterminal with just the ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
