Hi group members I am looking for KWP-1281 documentation. Can anyone help me because I do not know where should i ask or where could i get or buy it.(not the...
Hi All, Currently I develop an OBD2 diagnostic program, and I'd like to include in the program all car vendor specific information (Trouble Codes, enhanced...
The sample is attached! +++ Attachment: No Virus found +++ MessageLabs AntiVirus - www.messagelabs.com [Non-text portions of this message have been removed]...
... A good deal of DTCs for VW and Audi are on ross-tech.com ... There are also fairly complete lists in each of the Bentley manuals for these cars....
on a similar theme this simple interface you describe, is this true for later opel/vauxhall DTi's??? i have a zafira(astra) 2.0DTi and have been diggin around...
Hello Kevin I guess the diesel model may be CAN-BUS . If it is the case you can get our multiprotocol chip or complete mounted and tested OBDII/EOBD interface ...
the populated pins on my zafira seems to be ISO (3,4,5,7,12 and 16) so I think it rules out CAN-BUS I'm just a bit confused as to which one to buy don't mind...
Your Zafira diesel 2.0dti have ECU EDC15M or PSG16 Bosch, both with kw2000 fast init. Use Sanders kw2000 prog and a simple 2-transistor interface or max232...
many thaks for that radix will sort out an order for parts and see if i can make the interface Kev ... From: radix To: opendiag@yahoogroups.com Sent: Friday,...
Hi Group, Does anyone have a schematic for the dongle/Interface required for the above mentioned software in the files section? Tks in advance, Dave...
Hello, This email message is a notification to let you know that a file has been uploaded to the Files area of the opendiag group. File : /Tachopro...
opendiag@yahoogroups....
Sep 5, 2004 3:16 pm
3855
Hi have you schematic diagram for this tacho eprommer ? Boguslaw ... From: opendiag@yahoogroups.com To: opendiag@yahoogroups.com Sent: Sunday, September 05,...
Hello everyone, I need dump of tacho of BMW 318 IS year 93 type E36. If possible 130.000 Km SW:20.0 HW:6.1 What EEPROM is inside? 93c46? 93c56? Best Regards ...
Hi all, Does anybody know, whether it is possible to open/close windows, central lock by means of sending correponding signal in any OBD2 protocol? Any way, is...
... It seems reasonable. I know you can program Audis to do so with the use of their remotes. There is a thread somewhere on www.audiworld.com .... Also for...
Hello, i've send a diagnose software for bmw engine with siemens ecu (ds2 protocol). It is'nt complete but the principal function works good. This software is...
Do you know if it reads other faults like airbag, etc? The standard header for ecu request is 68 6A F1 and I think we have to change this header to access to...
Now it don't trasmit airbag faults. i'm wait to receive information about. ... ___________________________________ Scopri Mister Yahoo! - il fantatorneo sul...
peugeot 206 1.4 1999 Can anywan tell me pin location of k line on this car(j1962 con.) I dont think its on 7 because ,when ignition is off i still have 12.33...
made a 2-transistor interface for the 2000 zafira DTi downloaded the kw2000 program started program opened port so far all seems ok plugged into OBD socket but...
hello, I am trying to start a communication with a VECTRA B 1998, and have no sucess... Anybody have a circuit for ISO 9141-2? And a example in any program...
First check your 2-transistor interface with voltmeter. On open K-line about +10.5 volts, when you short k to ground level on Rx must change. Plugged into OBD...
thanx radix will double check it all tomorrow also found i may have problem with XP on the laptop, as i have trouble installing some software now cheers Kev ...
And one more thing. On 1 pin in Peugeot OBD socket is the power supply for engine ECU, and if u put there low level u will have some problem with turning on...
Excuse at all but from yesterday i'm trying to upload the D.A.B.E. software on group files but it'is impossible because the maximum file size is about 4 Mb and...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
