hey you guys i was wondering i just want a cable that goes obd ii to the printer port then i want to make a program to go through that port and get my...
Okay, try again, does anyone know the exact format of 9141 communication. I think its 1 start 1 stop and even parity, 8 bit data at 10.4K. I assumed the BMW...
Hi Julian, My BMW from 2002 has only a OBDII connector. On Pin 7 and 8 I can contact the control modules. Communication is DS2 protocol 9600 baud, 8 bit, even...
Hi! I've build a new interface with MAX232. It woks fine with VAG-COM, and VWTool, but i have the following problem: The programs can't find the Airbag module....
Hi to all and Happy New Year! I'm trying to find out in BSI firmware some diagnostic commands... Could anyone help me with details of starting diagnostic...
Hi, I need good dump or info for reset crasch data .. FIAT BRAVA 46413633 eeprom: OKI 951 smd FIAT MAREA 1.9JTD 46550647 Mcu: 68HC908AZ60 FIAT STILO 46835522 ...
Thanks markus, although playing about with this is doesn't seem to be what my peakresearch tool is putting out. I'll play further. Never really understood...
jHello I have a Toyota Corolla 2003 Damaged SRS Module. Can you please clear the crash data on this 25040 eeprom Writing on the module is: Module#210206539A ...
Hi, So far as I know ISO9141 was first, BMW starts with ISO9141 on DME11/31/33/40 protocol name KW71 (similar KW1281 VW) and with DME41 come DS2. Today it is...
I think pinout it's the same like 16F . ... From: "darqss" <darqss@...> To: <opendiag@yahoogroups.com> Sent: Monday, January 03, 2005 11:23 AM Subject:...
Hello all, hello Julian, Send this to a DS2 Motorelectronic and you should get a reply. 0x12 0x04 0x00 x016 <ecu addr> <lengh> <data> <XOR of all previous...
Confused by this. My peak research tool has been told to look up the DME fault codes. This tool works on all manner of BMWs. I personally have a 1991, 1995,...
Hi guys, my car is a E46, build in 2000. I used a MAX232/7404 interface. What I found out in the meantime is the following: It responds to some OBD-2 requests...
@mrtn: If you have both connecter (20 pin and OBD2 16pin), only the DME can be reached from OBD connector. I think pin8 on OBD2 is not used at your car. The...
Try L pin 10, K pin 15 ... From: "darqss" <darqss@...> To: <opendiag@yahoogroups.com> Sent: Tuesday, January 04, 2005 8:56 AM Subject: [opendiag] Re:...
Sorry if not clear. Currently I have the peakresearch tools K line connected directly to the Rx line on the PC. No car involved. On an oscilloscope the peak...
Hi all, is possible bypass immobilizer in VW group via OBD software or read immo code ? Its possible if is MCU locked ? Is there exist any solution ? Thank You...
with the new ross-tech 4.04 software: 1. is possible to run with the old interface (3 transistor and 3 optoisolator) or not? if not where i try the schematic...
hi, i have the new golf-5 with the original car-bulgar with remote key-control...but when i close my car ONLY blinks the light (azzard light) but no BEEP from...
Would the same apply to a '97 Cabrio. Once upon a time it beeped. Now it doesn't. It quit about the time that I replaced the battery (no power so everything...
... This is somewhat of a long-shot, but I remember reading somewhere that the interfaces most of us use between our laptops and ECU's invert the signal on the...
You can change your alarm settings by going to the Central Comfort System (46) then change the adaptation fields 1=ON 0=OFF channel 6 = Unlock beep 7=lock beep...
for UWE o an big-expert: in my GOLF-5 what channel and setting i set for: 1. when i close the car with original VW remote-control (car bulgar vw) the system...
Hi All! If someone have pinout for this ECU, please send it: Magnetti Marelli year 1999, engine type D7F PLF 7700224699 HOM 7700105560 SFR 200 Regards Bosti...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
