Dear Sirs. I have found in the Ford TIS CDROM (Technical Information System) that the Ford Escort communication connector (16 pins like OBD2) use in Argentina...
Sergio: If so, yo should be able to communicate thru ELM323 interface and ScanTool soft. However it´s possible that the init string or heders from ELM...
hi , i need immo off solution for 1.5 crdi hyundai getz - dump from engine ecu in attach BR marko [Non-text portions of this message have been removed]...
hi , does somebody have virgin flash dump for 200 kompressor c203 with engine ecu siemens 5wk90490 and MB number A2711536279 BR marko thanx in advance ...
hi , does anybody have paired dump from p206 1.4 hdi with edc 16 inside and bsi - 95160 inside both of them ? thanx in advance its quite urgent [Non-text...
Hi, Can anybody tell me how to read DTCs and reset faults on a 1999 Daewoo Matiz airbag ECU (Siemens part no. 96 314 932)? The engine ECU is on ALDL but the...
I have a 97 Audi A4 1.8T. It supports KWP-1281 (VAG) and ISO-9141 (OBD-II). I am writing my own scanner. My question relates to ISO-9141. After slow init of...
Hi, can anyone point me in the direction of a free software download for Vauxhall / Opel Diagnostics? the Car i need to check is a 2004 Opel / Vauxhall Astra,...
Hello, you can use the free trial version of OP-COM from Car-Soft. http://www.carsoftmft.de/downloads/OPCOM_DEMO_070319_DE.exe It uses a normal K-Line...
I am writing a scantool for my 97 Audi A4 1.8T. I can communicate (request DTCs, erase DTCs) with the following controllers, all using KWP-1281: 01 Engine...
Hello, I need to connect diagnosis with the DLC of a Ford Focus 2001. I think could be ISO 9141 but I´m not sure... Moreover, what software should be a good...
It is J1850 PWM for engine diagnostics. You will need an interface cable, like www.obdkey.com From: opendiag@yahoogroups.com [mailto:opendiag@yahoogroups.com]...
Re: VAG KWP-1281 comm problem More info to previous post for clarification. The comms is std KWP-1281 ... *Send 0x35 (7O1) at 5 baud <---ECU I want Receive...
Hi. I am trying to learn about obd-II and CAN bus. I have many questions, like what CAN addresses the test tool should be, what addresses the ECUs should be...
Lou. Most libraries will not loan out reference material. Joe ... From: lfaustini To: opendiag@yahoogroups.com Sent: Wednesday, January 02, 2008 11:35 AM ...
... Hi, Just tried that. It does respond with KWP-1281 init info, but no block of data is received. I have tried other baud rates as well. This ECU will...
I don't think the baud rate is the reason. Try to reduce your 50 ms delay. Actually I send the 0x09 block to ECU immediately, without any delay for KW1281....
Hounddog1071 & Darqs, Thanks for your suggestions. I will try both of these and post back the results in about a day. If my thinking of <P3> wait is correct,...
hi , i would need a good dump for the motometar 1j0919860 MM0 with 24c02 inside. my dump is damaged. thank you in advance BR marko [Non-text portions of this...
No need to wait til tomorrow! Found time this evening to check mods. I tried reducing the 50ms wait; 1st to nothing, next to approx 5ms. In both cases the...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
