Hello there! I have an ECU that responds to an L-line 5 baud init on address 0x19 and sends back 0x57e5 on the K-line at 10400 bps. Have you come across this...
Hi colleagues, I'll need develop a boot loader via K-Line for VW using KWP2000. I've already worked with this protocol in the past, but I know almost nothing...
Hello again! After confirming the 0x57e5 (0x1a) the ECU sends 0x02383a I think this means: 0x02: 2 bytes follow 0x38: data 0x3a: checksum (0x02+0x38) However,...
Do you have the spec? Regards, Andrei ... From: hounddog1701 To: opendiag@yahoogroups.com Sent: Tuesday, July 29, 2008 11:16 AM Subject: [opendiag] Re: ISO8 ...
Hello Andrei, I am replying for Paul Bowen, our Chief Engineer, who is out of the office until Tuesday, August 19th. He is checking his email while on the...
Paul Bowen
paul@...
Aug 11, 2008 10:45 pm
8038
hi i need rover 620SI (not turbo,1995 year) original ecu dump! Best Regards!...
Hello I have a diagnostic device with the error in my car out. Unfortunately I only get an error code without any description. Now I'm on the search for BMW...
Hi I'm in trouble with a bosch ECU 0281001214 (opel omega 2.5TD 1994). I wrote a little piece of code that wakes up the ECU at 5 bauds with address 07 , grabs...
... Why don't you set your timeout to 1000 ms to clarify this ? Make sure you get the correct echo of your 0x7F. Try a delay between 0x80 and 0x7F of 25 ms or...
Hello ! I have a Fiat Brava 1.6 16v 1996 ecu type IAW1AF13, diagnosis conector with 3 wires in engine compartiment.What interface and software can i use for...
A "KKL" interface with 3-pin adapter. You will need the KWP71 software. 2008/8/28 George <mandaxcdd@...> ... [Non-text portions of this message have been...
A interface like VAG ? I use this interface with a custom made adaptor with 3 wires and kwp71 ...No work. You have a tested schematic diagram please?...
I use one I bought on eBay, sorry, no schematics. What do you mean with "No work" Could you show the errors you are getting? [Non-text portions of this message...
Hi , I tried delays as you said , and... nothing ! According to the disassembly of the ECU code , it only waits for 5ms between 0x80 and 0x7F. So I wonder if a...
Hi :) Anybody can check this pinout for IAW 1AB: 36,54 - B- 35,13 - B+ 12,31 - K and L line Which pin is K line: 12 or 31? I want to connect ecu "on the table"...
I have one of those Carsoft 6.5 knock-off interfaces. It seems to work okay on my 1996 328i. Is there any benefit in trying to get the SP1 or SP1.1 software to...
Hi! I also have Carsoft 6.5 "spin off" as you call it. The Chinese one I suppose with two LEDs. I would recommend INPA / EDIABAS for use with your cable,...
Hi, I have the same 2-led Carsoft 6.5 adaptor I guess. I have it working okay I guess. I can get to the SRS & others fine but I cannot get to the ABS module....
To get INPA/EDIABAS 5 I suggest you try usual channels like emule/edonkey and torrents. Some russian WWW sites also have this stuff. A good discussion site...
Hi I'm back my timing issue. In fact Windows doesn't handle serial data fast enough , causing the ECU to reset the connection.( The ECU sends 10 times the...
Darqs Which vehicle is this from please? From: opendiag@yahoogroups.com [mailto:opendiag@yahoogroups.com] On Behalf Of darqss Sent: 29 August 2008 12:03 To:...
Set the buffers in the serial port config to 1 like Sander suggested. 2008/9/3 hackwell33 <hackwell@...> ... [Non-text portions of this message have been...
Hi Wizzman I already tried Sandr's tip and it doesn't work. in fact my problem comes from windows API Readfile that takes forever to return , causing a...
Hi! I'd like to read the parameters of a engine ECU(my car is a brazilian Chevrolet Celta Flexpower). It uses kwp2000 protocol and doesn't support J1979...
Hi If your are talking about services 21 it's not addres but local ID. If you want use addres it's service 23. What is your ECU brand ? Cheers ... parameters...
Magneti Marelli IAW 1AB is for Brasilian applications, but the pin for k-line is the same of Fiat or Peugeot applications (IAW 1AF or IAW 1AP). If you find one...
Hi All! Pls somebody send me original flsah to Renault Master 2,2 DCI ECU. Renault Master DCI 0 281 010 787 Regards FT [Non-text portions of this message have...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
