Hi, I have following different build-it-yourself MP3 jukebox projects and pjrcmp3 looks really promising. However I fail to find any descriptions or pictures ...
I've noticed this too. It takes a while to set in though, and can be stopped by typing NDEBUG. (Nice discovery.. no-one thought to tell me that bit. :) Was...
Hello. Playlists are not yet added, in that adding your own M3U files has no effect until software is written for that. I think that is high on the agenda...
I've gotten back another drawing from the EL sheet company. I have posted a picture of it in the yahoo message board. all seems fine except im not sure if...
The build page is now back online and running once every 6 hours as before. If anyone has any problems with the new builds please let me know. Thanks. ...
Im sure its because of the massive amount of text being generated and sent to the serial port. It would be nice if you could use debug to look at sections of...
... Short story: Yes, this is a known problem. It will not be "fixed" until after the new smarter caching strategy code is fully debugged. Longer answer: ...
looks good, you should be able to trim off a couple of mm off the top and bottom no problem. it doesnt really matter too much if the tail comes out of the top...
Thanks for the info Paul. I do think clock_tick() is a bit too course for the timing I want. With timer0 (currently) unused I should be able to setup a good...
ok i just got the kit and im ready to build it but im still nervous about the SMD IC's they look easy to solder but i noticed on the PCB where the SMD...
when you made the assembled MP3 player kits did you or someone else hand solder the componets to the baord or did you hire someone to do it in some sort of...
... I was using 0.6.9 since it was first released.And yes it is by far more stable than 0.6.8 and before. but I still had problems with my rev c board after...
Apply a _tiny_ bit of solder to one of the corner pads. Put down the IC, heat the PAD where you've put the solder, and it should reflow nicely around the pin....
now, this may not be the correct way of doing things, but its worked well for me in work, generally I put a small blob of solder on just one of the pads on the...
Dean
woodyatt@...
May 1, 2002 7:10 pm
2311
... Most of the rev C boards have been assembled by a company we hire to build them. They require a qty 100 minimum to do the work (at a reasonable cost). I...
I bought a power pack that works now, (273-1779 someone posted about it earlier) I can use the buttons on the player board but not the ones that come with the...
Im seeing the directory name on the LCD screen becoming garbled. It happens on the same character in the directory name. I have all my files sorted by...
Hey how do i connect the IDE cable??? they all have a filled up pin in the center but on the MP3 board it has all the pins do i need to cut one of the pins if...
you can cut one of the pins (that's what I did.) You can figure out which one by lining up the IDE connector with the cable _MAKE_SURE_ that pin one is in the...
Does anyone know if this pin is implemented in the firmware yet? i.e. if I pull /IDE_DISABLE low, does the firmware actually stop trying to access the drive,...
While trying to capture the directory bug I was explaining. I was abileto capture the ide interface going very wrong. The following is that capture. Including...
ok the LCD display works fine and the buttons on the mainbaord work great but when i try to use the LCD buttons whenever i press one of them it says B0_DOWN ...
just to let everyone know, mainly Paul since im sure hes the only one interested but i just got done soldering the kit together and to my luck after...
hey im using the .0501 firmware witch is the last stable one and my LCD screen displays the name of the song with some hex numbers but on the main www.pjrc.com...
... You need to have the LCD connected when you boot the board. If you plug it in after the firmware is already running, this is what you'll get. Someday the...
... I do. ... trying to ... No. It should detect this and go into a loop that waits for the IDE_DISABLE to be released and then restart (everything needs to...
... My best guess is that your SIMM is just barely working with 0.6.10. It is frustrating, I know, and I'm quite frustrated that there's so much variation...
From what I can tell of the capture code,It looks like the memory that is holding the fat32 information may be getting corupted. As for the other bug with the...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
