... Joshua Goldberg <psychochef50@y...> wrote: ... Just how and where would the air valve exit in such a case? Jeff [Non-text portions of this message have...
Changing the gear ratio on a rear freewheel. Are all freewheel gear threads / holes the same or do they have subtle size differences! As long as you swap over...
Not sure you can see the valve in this pic, it is there. ... Joshua Goldberg <psychochef50@y...> wrote: ...you could actually put the tube and tire directly on...
John Not sure what you are asking, the Ego2 uses a 406mm (20 inch) front wheel and so this 10 inch hub will fit...although you'd lose the disc brake. The 2nd...
Hi Mark. Thanks for the reply - that's what I felt was the case but I cannot find out if this is truly the way it is. I felt as the freewheel has been around...
This has been a problem to exit the motor with a valve. I have had a lot of experience with this before I got involved with Kenny. What I had to do to be...
Yes they are ... From: brucepeter2002 To: power-assist@yahoogroups.com Sent: Sunday, February 01, 2004 7:57 AM Subject: [power-assist] Help with Freewheel Gear...
Hi all. The reason I posted the question is I changed the 6 speed Shimano gear over for a 6 speed Sachs / Maillard gear on my hub motor. I have been informed...
Ron Nice to see at least one person deals with American Airless. ... Later on we got tires from American Airless and didn't have to deal with the foam fill...
Joshua; I was perusing the Crystalyte site and find the specs a little confusing. 1) The 4011 48V motor for example shows a draw of 15 amps and a power rating...
Hi Jeff So you find the numbers confusing? We like to make the numbers up just to keep Colin Dedman on his toes. As for #3, a 36V and a 48V motor are the same,...
... Yep Joshua, 57.6V Nominal, charges up to around 69V. Unfortunately my Whattmeter is limited to 60V, above that the display starts spewing gibberish when...
... Colin, What drivetrain efficiency are you basing this on? Do you mean best in a competion with direct-drive hub motors or with all systems including those...
... round ... best ... read, ... input, ... hub ... figures, ... motor ... All of these conjectures will be put to the test when 250+ lb Jerome Byrd of ESW...
http://autos.groups.yahoo.com/group/zappy/message/50161 You need to 'Up Thread'/'Down Thread' a little to get the complete picture - but there it is! I know...
Hi - I see references on this list over and over and over to Kenny. No one gives a website or company name or contact info. Who the heck is Kenny? website?...
Kenny..."South Park", the less animated Kenny is at www.crystaltye.com ... Hi - I see references on this list over and over and over to Kenny. No one gives a...
sorry about the South Park Kenny/ "Kenny Lam Yung" is the Main Fuse at Crystalyte Motors Joshua ... Hi - I see references on this list over and over and over...
Whoops...I misspelled Crystalyte. www.crystalyte.com Joshua ... Kenny..."South Park", the less animated Kenny is at www.crystaltye.com ... Hi - I see...
I may be able to say something here I believe the power noted here is output power ... they have the motor hooked up to a generator and test the power produced...
Mick I wonder if you have a 1000uf electolytic capacitor installed near controller ( across the battery wires) to stop the whattmeter screwing up the display? ...
Peter Just a note here with the power on...my motor rolls freely forward and gives quite a resistance in the reverse direction... I beleive this to be...
... Thanks David, I might give that a go, have you tried it? I've removed the whattmeter for the moment. Any idea what voltage this mod would work up to?...
... Jerome ... Not really John, Randy's setup subjects the hub gears to twice the motor power plus human power. Do you know what gear reduction ratio the...
I had the whattmeter problem of the display going blank and scrolling under power and talked to Bob at astroflight and he said that if the wires from the...
I have'nt a clue. Actually the real test will be when the mod guys get around to playing around with it - dual motors, E-Tek, etc. The Currie motor plate is...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
