Hi; Does anybody have a part number for a ' Level of Ink Sensor ' for a Tectronix Phaser 360? Thank you. Paul All outgoing mail certified virus free by Norton...
Roberta I have a similar problem with one of my repairs; full page ghosting- mainly in black. A new transfer belt solves the problem immediately but the...
Remove paper tray and release duplexer tray. Physically bend up on the metal tray a little. The duplexor tray does not close all the way thus creating the...
burt_hurt
sicem@...
Apr 1, 2003 2:01 pm
10347
Sure, should have thought of that, although it's not so much an error code as a message "28 Load Paper Tray 1 Letter" That's it. Like i said it winds up as if...
LJ 4000 - In a classroom. Original problem paper jam behind tray 1. After jam was cleared paper would feed through machine from tray 1, but if I fed from tray...
I had this problem on a 4100 a few weeks ago, change the ECM board Paul ... All outgoing mail certified virus free by Norton AV 2003 Shop & Buy at my Ebay...
My first best guess would be that it tries to pickup but the gum rubber "D roller" rubber is shot (dried, not sticky, etc) and can't pick from the tray and...
I have a HP LJ 4+ which sends the paper out with a lengthwise fold on the right side of the printed page? I had an extra upper delivery roller, so I installed...
Sounds like the fuser. Open the back door and defeat the door interlock. Send a print thru the printer and catch it as it comes out of the fuser. I think...
Yes. You can verify it by looking at the printout on the paper. If the problem is the fuser, the print will be straight on the paper (and maybe even under...
Greg Prevost
gregword@...
Apr 1, 2003 7:20 pm
10359
Generally caused by the fuser roller when the non-stick coating (or film, depnds on fuser) breaks down and allows sticking of toner, and paper. ... From:...
One way to see if it is the fuser vs the output rollers is to open the back and let the paper exit the rea rather than through the face down (top) output...
my cano bjc-2110 prints only colored horizontal lines and wont print font or reconize grafics...
jfioskie
jfioskie@...
Apr 1, 2003 8:04 pm
10362
try a new cartridge, could be dry could be the carrier/printhead has dry jets could be the driver software has gone corrupt- uninstall and reinstall could be a...
My printer in working condtion was on auto power Off mode but did not wake up after all efforts. I opened Main board, all fuses are Ok. But still not getting...
rtj1010
rtj1010@...
Apr 2, 2003 2:16 pm
10364
I have a noisy paper pickup on about one-third of the print jobs. If it starts noisy it stays that way for the entire job. The printer is brand new, 20k...
It depends on the noise I recently had a 4100 under warrnaty that had a noise that wa a bad output roller making a squeak so it was fixed under HP's dime. Try...
Hello! I have an Optra Lx+ and an Optra L. The duplexer works like a champ in the Optra Lx+. I get a paper jam (23) every single time I use it on the Optra L....
nope43212000
nope43212000@...
Apr 3, 2003 2:01 pm
10367
Once again thanks for the help on HP LJ 4500- Tray 2 would not paper feed. Turns out it was the metal piece on left side about three inches in from edge, once...
I've had duplexer tray problems due to 1) the tab that holds the lid of the duplexer try at a certain height is crackd, out of place or broken off 2) the...
Stan- Using OEM rollers is important. Many people discuss removing filings from the clutch although we have rarely found that neccessary. We have found that...
Check the Triac on the main power board. Had the same problem with mine, it was DEAD...no power at all...Replaced the triac. Look for a heat sink as it is...
Hi all, I've had my first HP Color LaserJet 5 in the shop today, it's damn heavy ! Anyway, it's got a strange fault which I'm really not sure where to start. ...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
