Regarding the feed issue that both printer have, I have seen a problem with the HP 8000s (newer than the 5Si) where they will continually jam feeding letter...
i am very sorry but the error you say is not a i/o error but a fuser error ( all lights on service error ) press go button to enter service code ( go and ready...
Correction the Ready and Go do not indicate an I/O ERROR on the HP2200. I was looking at the HP2100 light patterns. I also checked the ribbon connection...
brendan_hoefer
hoefer@...
May 1, 2003 1:05 pm
10771
Hmm - I just skimmed the old messages and never saw one from you about an Optra N. Refurbished units vary with refurbishers, never had a Lexmark rebuild go bad...
Hi, It was msg 10389 dated 4/7/2003, but it doesn't matter. I have cleaned the Second Pass Roller, replaced paper pads and Transfer Roller. I had to change the...
For my two cents worth! I have found rebuilt PIU units not to have the same quality as new. The price difference is less than $80. now. I do replace 2nd pass...
If paper jam is only from tray 3, I really knows what is going on. Is the second pass roller. I have repaired about 25 units and all of them had same problem. ...
The pcl switch on the printer will need to be replaced or the piu assembly. One of the two is causing the problem....
jgamon
jgamon@...
May 1, 2003 6:49 pm
10777
wrong if it is jamming from t3 not t2 then the problem is the small dum bell roller (rb1-6561) if its jamming from both replace 2nd pass roller and sensor...
Joe, we have these Tray 3 clutch gears, it's a 16 tooth gear with a one-way clutch inside it; it fixes most jamming problems with tray 3. I usually replace the...
Jim O'Connell
joconnell@...
May 2, 2003 2:31 am
10779
Okay you guys. You really want to know what the problem is... If paper feeds from Tray 2 and Jams from Tray 3 only? Then it is most definitely the SECOND PASS...
Hey yall, I know this isn't the right discussion group for this, but if anyone has a company in the SE Texas region and wants a Printer TECH, I am available. ...
I would like to know if anyone has changed this part, and what has to come off to change it. Book has no help. It looks like it could be a little tricky....
A while back somebody was asking about this printer and a service manual for it. I don't have the service manual, but I do have a fact sheet which covers a lot...
HELP! I purchased a used Okidata ML 320 Turbo 9 pin dot matrix printer and I'm having a heck of a time making it print! I'm running Windows 98. I have the...
Shelby
sumthin92@...
May 2, 2003 6:47 pm
10785
Go to Okidata's site and see what drivers that printer emulates. One will be IBM and one will be Epson. It seems there are two versions of the 320. One uses...
Chris Sawtelle
csawtelle@...
May 2, 2003 6:55 pm
10786
I think ones that work are IBM: Proprinter & Proprinter II Epson: FX-80 ... From: Shelby To: printerrepair@yahoogroups.com Sent: Friday, May 02, 2003 1:45...
Chris Sawtelle
csawtelle@...
May 2, 2003 6:56 pm
10787
First try setting the printer to the "generic" TEXT PRINTER in the Win98 list of printers, usually first or second on the list, or redirct something from DOS...
This isn't the clutch I was talking about, the clutch assembly is the intermediate clutch. Open the right side door and you will see two small black rollers....
Folks- We have a couple of these Tektronix wax printers with partially clogged heads. Repeated cleanings only waste ink. There is supposed to be a service mode...
I know exactly your problem, the printer is just keep feeding paper through sometimes prints some symbols. You have a turbo printer. You must use a turbo...
Hi, does anyone have a win98 drivers for this printer ? or compatible driver ? I try to search the net but there is no where I can find. it seems there is no...
... intended ... expressed ... sender ... [Non-text portions of this message have been removed]...
Bob
bobjones@...
May 5, 2003 12:39 pm
10793
I have an hp inkjet that works well except the letters are not aligned correctly at frequent intervals on the page. This seems to occur when the paper is fed...
Fcurtis29@...
May 5, 2003 12:39 pm
10794
... I have replaced this part before and it is not very difficult - just a little time consuming (took me about an hour). Basically, you have to remove the...
Check and see if your printer port is set to ECP in you BIOS. If it is, set it to SPP or normal. An ECP setting can cause the problem you describe when using a...
Help! I have a epson 600 color stylus printer, but it just wont print after I request a page to print, the computer seems to being sending the message to the...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
