Hi Guys, On this 2200 the attention light keeps flashing... I have checked: Paper path and sensors Cart in printer Paper tray full Does anybody have any...
One of my customers brought this machine in for repair because of this message and we replaced the drum for them. Problem is that we couldn't find a way to...
Hi all, Well im still working on this 2100 without a manual(lots of fun)...and I am not able to determin what "error" the light pattern is indicating..the...
Help Anyone got any other ideas besides the fuser? I installed a new fuser and I still get the same flashing lights and the fuser is cold. What would be the...
It looks like a general fatal error in the manual, it says to remove all accessories and turn the printer on, if the message is gone,replace them one at a time...
I have two 1220C printers. Both printers worked last year. They belong to a local school. Worked at the end of the last school year. Would not work in...
Tim, Have you tried a different toner cartridge? Sometimes a defective cartridge can cause this error. Also, if the toner is not properly seated in the...
Dave, If you jumper pin 1 to pin 2 on the mini din connector on the back of the printer and turn the printer on the printer will do an extended POST which ...
Mvelden
mvelden@...
Jun 4, 2003 1:33 am
11123
Ours is smudging. So then it would probably be the fixing film over the laser heating assembly? Isn't there a kit I can order to fix this? I've never done it,...
I did not see the original post but here is what I know :) did wait for the printer to reset before trying the new fuser? on some machines if you don't wait up...
Ok I know this has nothing to do with printer repair but I had to send this out - of course it's a little demeaning and profane but it gets the point across to...
I have a HP 4100 that has a 49.4210 service error. I have tried a new jet direct card with the same error coming up. Has anyone had this problem. Could anyone...
grenco77
mcmahon130@...
Jun 4, 2003 1:35 am
11129
I have the service manual for this printer, I looked thru it yesterday, but I don't have the time to look up every code, contact me email at ...
From the service manual: 1. Drum counter When I/D unit reaches run-out time, "CHANGE DRUM" is appeared in LCD. Under above condition, user can see the Drum...
Hello Heather, a common cause of 41.3 errors, almost all in my experience, is related to a gear in the input assembly, at the end of the feed roller shaft....
Hi, I have a problem with a HP Business inkjet 2200 Control panel displays : Install black prn. head or is missing I have cleaned prn. head and it will print...
printerlink2000
printerlink2000@...
Jun 4, 2003 1:38 am
11135
Hello! Where can I get printer parts for a good price in New York City (Manhattan) for a Xerox WorkCentre 950? Thanks in advance for your response Bitsi ...
I´ve a hp deskjet 610 printer. And yesterdey when i try to power on, she not responded. I check the power wires and nothing happened. I don´t know... ...
My Laserjet II pulls paper from the paper tray without any problem, but as the paper hits the first roller assembly it slows up and this causes it to curl up...
srg509
srg509@...
Jun 4, 2003 1:40 am
11138
This is my first time doing this, looks a little tricky. Plastic piece that holds spring is broken, it looks like shaft will have to be removed. I looked in my...
HI THE MESSAGE POINTS TO A BAD FIXING UNIT , YOU WOULD NEED TO REPLACE THE UNIT , AND REINITIALIZE MACHINE IN MAINT. MODE #91 AND THEN EXIT MAINT. MODE BY...
HILL
hillel284@...
Jun 4, 2003 1:41 am
11140
Folks_ We have an NEC 870 Laserwriter that is in working condition except for outputting garbage in the printouts. Seems like the formatter pcb may be ...
Thank you very much, Russ, for providing this manual. I downloaded it without problems - though, until the end, I didn't know whether it actually was...
First off, what do you mean by not start? Does the light come on briefly then go off. If so then check you read door. If it isn't in and latched it will...
I've changed a few of these, they are tricky. The hardest part is getting the C-clip out (without it falling into the drivetrain) and then getting it back in...
Jim O'Connell
joconnell@...
Jun 4, 2003 2:03 am
11144
World Of Fax in NY http://www.worldoffax.com/ ... From: "Bitsi Itsi" <bitsi200@...> To: <printerrepair@yahoogroups.com> Sent: Friday, May 30, 2003 6:56...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
