That was good timing - I just had a client ask about a source for them and now we can buy one set and see how they work out monetarily and functionally. ... ...
Yep ............ I finally took a day for doing this kinda stuff , and just went on line and contacted them myself. . Mike ............. . Visit our website @...
Hallo! I have problems tracking down an 13-PAPER JAM error. The rollers are all fine.. But the printer stops just after the paper hits the exit sensor flag. ...
... Jan, check the gear on the motor shaft. I have had a couple that broke (a 4L and a 4M), because the toner was solidified. HP would like you to buy a new...
The call I received was listed as "982 Service Engine Error". Lexmark lists it as "982 Service Engine Comm". The description had to do with someone moving the...
Jan-I would check the flag sensor on the fuser. You can tell by removing the fuser. Sometimes a previous jam will break one end of it and will not swing back...
My experience with this is either a bad comm cable (parallel) if conencted via parallel, or a bad engine board (aka formatter essentially). ... From: Mike...
Yep - this is a common thing for the LJ4, 4 plus and 5 - the sensor flag has two places it clips into and swivels in - it should cause the flag to swing back...
Thanks for the input so far! ... I don't see any broken edges or anything. It is swung up by the first edge of the paper and triggers the exit sensor. Is it...
Jan . My limited experience with this "EX" series has been that, . When it picks up the paper without a message coming up before the pick up, . it usually is...
Hi! A 982 Comm error come from the autoconnect plugs. You have one on the top of the printer for paper handling options, one under the printer for duplex and...
and if it is the nylon-like gear missing a tooth you can replace just that gear on the LJ 4 but on the 4 Plus and 5 you have to replace the gear set. I still...
I have to dig up my source but it's a fairly simple fret-based printer - the whole printhead will come off with a few bolts. My guess is (it's been over a year...
Folks- First one of these Lexmarks that I have seen. The printouts have horizontal banding throughout. Approx 1" vertical spacing between defects. The banding...
... Did you look at the fuser cleaner that sits on top of the fuser? Have run across banding problems caused by a run of label stock ruining the fuser cleaner....
Hi! Look here for the repetitive marks chart http://support.lexmark.com/cgi-perl/knowledgebase.cgi? ccs=229:1:0:332:0:0&framed=&docid=ENUS7512&relevance=1 good...
after a jam of any kind on my infoprint 32 it goes into a warming cycle after the jam is cleared.It then prints out an error sheet and the led says "printer...
Contact Nate at Data Reliance Phone 1-574-935-9550. The 6400 is just a Printronix printer and he is the best with parts and knowledge on these printers. Dan...
Sorry, the link dont work properly :( Try this one :) http://knowledgebase.lexmark.com/pubfiles/attachments/ENUS7512_Repeati ng_Defect_Chart_C750_en_us.pdf ...
I have a 5si that is feeding extra pages (not multiple pages)in long print jobs. It normally won't do it with shorter jobs (up to 15 pages). It will feed 2-6...
If you have an old core you can switch the plastic plate from the DOA to the working but broken fuser and not have to buy a replacement - I keep dead fusers to...
Hi All, I have a HP PSC 2110 with lights that blink rapidly right after turning it on. The scanner lamp lights for about 1/2 second then goes out. I wanted to...
... A Louisville slugger would be my first choice. If that's not available, the old reliable 40 ouncer usually does the job adequately. Yeah, I know. It's just...
Already replaced fuser unit 2x, it worked for about 1 day after each fuser was replaced, then replaced POWER SUPPLY STILL HAS 50.1 appearing approx. 10-20...
Having problems with message search?
Fill out this form to ensure your group is one of the first to be migrated to the new message search system.
